784920
38
Zoom out
Zoom in
Previous page
1/40
Next page
35
TROUBLESHOOTING
Should you experience any problem, do not hesitate to contact your authorized CALDERA dealer. Here are some tips to help you to diagnose and rectify
some more common sources of trouble yourself, if you choose to do so.
GENERAL OPERATION TROUBLESHOOTING GUIDE
Problem Probable causes Solutions
Entire spa is inoperative. Power failure / not plugged in
RCD tripped
Check power source
Reset RCD; call for service if it will not reset.
Spa does not heat; jets and light operate.
Display shows“ =====”
POWER & READY icon flashes
Pressure switch is open and should be closed
Pressure switch senses flow through heater even though the
jet pump is off
Check for clogged filter. The pressure switch will reset when the flow
of water through the heater has been restored. Call for service if the
pressure switch trips frequently.
Contact an Authorized Service Technician
READY icon flashes Control Sensor open or shorted Contact an Authorized Service Technician
Spa does not heat; jets and light operate.
Display shows“ ---------”
POWER & READY icon flashes
Pressure switch is closed and should be open Contact an Authorized Service Technician
Jets weak or surging Spa water level too low
Filters clogged / suction screens clogged
Jet nozzles closed / air valve closed
Add water
Clean filters / clean suction screens
Open jet nozzles / open air valve
Light inoperative Bad connection Contact an Authorized Service Technician
Display shows “- - - - “
(Entire spa is inoperative.)
POWER icon flashes
Heater high limit thermostat tripped Disconnect power to the spa for at least thirty seconds to reset the heater
high-limit. If tripping continues, clean the filter, then if tripping still occurs,
call for service.
After filling or refilling the spa: a jet pump is
operating, but water is not flowing from any of
its jets.
Pump is not properly primed.
1. Turn off power to the spa at the breaker and remove the
equipment compartment door
2. Loosen the union on the top of the pump(s) (as seen on page
17) to allow the air to escape, then hand-tighten the union(s).
3. Turn power back on, activate the pump and check to make sure
union is tight enough to keep it from leaking. Re-install pump
and equipment doors.
OR:
Remove and reinstall the FROG cap.
Service Information
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caldera Vacanza - serie 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caldera Vacanza - serie 2021 in the language / languages: English as an attachment in your email.

The manual is 3.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caldera Vacanza - serie 2021

Caldera Vacanza - serie 2021 User Manual - German - 40 pages

Caldera Vacanza - serie 2021 User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info