784921
23
Zoom out
Zoom in
Previous page
1/40
Next page
Operating Instructions
spa under normal temperature demand. However, when in Sleep Mode,
should the spa call for heat, the pump and heater
will be suspended after
Filter Cycle 2 (F2) until the activation of Filter Cycle 1 (F1), at 8:00 a.m. to
minimize pump activation during quiet evening hours.
Important: Power-up of the spa starts the F1 sequence. In order for the
sleep mode to work in the evening hours, the spa must be powered up in
the early morning hours. The Sleep Mode will always be active the 6-12
hours between the end of (F2) and the beginning of (F1) depending on
how the filter cycle program is set.
Note: If temperature drops below 27º C (80º F), heater will automatically
activate to prevent spa from freezing.
To activate Sleep Mode feature:
A. Press the MODE ( or ) button until
the TOOLS screen is displayed.
B. Press the (
+)
button to enter the TOOLS
submenus.
C. Press the MODE ( or ) button until ECON is displayed.
D. Press the (
+)
button to activate Sleep Mode. Moon & Stars icon will
appear on the screen of the control panel, indicating this feature has
been activated.
To deactivate this feature, simply repeat steps A-C then press the (
-)
button.
FILTER CYCLES
When the spa is first powered up, the automatic filter cycle will wait 10
minutes before starting. Your spa will automatically turn the first filter cycle
on for 60 minutes on low speed. The second filter cycle will activate for
30 minutes, 12 hours later. The filter cycle icon, F1 or F2 will be displayed
in the control panel during the filter cycle.
NOTE: The optional ozone system only works d uring the filter cycle.
To modify the length of either filter cycle:
A. Press the MODE ( or ) button until the TOOLS menu is
displayed.
B. Press the (
+)
button to enter the TOOLS
submenus.
C. Press the MODE ( or ) button until
FILT1 or FILT2 is displayed.
D. Press the (
+)
button to enter FILT1 or
FILT2. F1 or F2 icon will flash.
E. Using the (
+)
or the (
-)
button, adjust the
desired filter cycle time, from 0 to 6 hours.
F. Press the MODE () button in FILT1 to go to the RESET screen.
Press the (
+)
button if you want to reset the filter 1 starting time to
the current time or press the MODE () button to go the the EXIT
screen. Press the (
+)
button in the EXIT
screen to go to the FILT2 screen.
The filter cycle will activate the jet pump on low
speed for the entire cycle. When activated, the
filter cycle icon on the display is turned on. If
the temperature exceeds the set point by three degrees F for more than
three hours, the system will cancel the filter cycle for the remaining filter
cycle time. Should the temperature cool down to 1°C (1.5°F) below the
set point before the end of the cycle, the cycle will resume for the rest of
the time. Should you use the spa during the filter cycle by placing the jet
pump on high speed, the Filter icon and Jets icon will be on. Once the
jet pump has been shut off, a ten minute tranquil mode begins (Filter &
Jet icons are off during tranquil mode while F1 or F2 remain lit). The Filter
and Jet icons will come back on once the tranquil mode ends if the filter
cycle timer is still on.
BRIGHTNESS - LCD
If you would like to change the brightness of the Control Panel screen:
A. Press the MODE ( or ) button until
the TOOLS menu is displayed.
B. Press the (
+)
button to enter the TOOLS
submenus.
C. Press the MODE ( or ) button until LCD is displayed.
D. Press the (
+)
button to enter into the LCD menu.
E. Using the (+) or the (-) button, adjust the desired screen brightness.
AUDIO MENU (OPTIONAL)
The following applies to spas that have an optional wireless audio system
installed:
When the wireless audio system has been installed on the spa, the
control panel can be used to control the audio system. The following
information demonstrates how to navigate the music menu by using the
spa’s control panel.
AUDIO MENU
Once the music system is installed, an AUDIO
menu will be accessible on the control panel
screen.
To access the menu, press the MODE ( or )
button until AUDIO is displayed.
BASIC CONTROL PANEL OPERATION
1. To enter into a sub-menu press the (
+)
button.
2. To move to the next menu press the MODE () button
3. To exit from any sub-menu, press
MODE ( or ) button
as many
times as necessary until EXIT is displayed then press
the (
+)
button
to exit that sub-menu.
TO TURN AUDIO SYSTEM ON/OFF
From the AUDIO screen:
1. Press the (
+)
button to display POWR -.
2. Press the (
+)
button to display POWR +
and turn the audio system ON. Press the
(
-)
button to
display PWR - and turn the audio system OFF.
IMPORTANT: The power can take a few seconds to turn on or off.
TO PAIR BLUETOOTH
On your device, find My Spa BTXR. If you DO NOT see this, another
device may already be connected (see To Disconnect Bluetooth on
following page).
1. Press the MODE ( or ) button until the SETUP screen is
displayed.
2. Press the(
+)
button to display one of three audio sources, BLUE,TV,
AUX in the setup menu. Bluetooth should be selected.
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
20
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caldera Vacanza - serie 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caldera Vacanza - serie 2020 in the language / languages: English as an attachment in your email.

The manual is 3.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caldera Vacanza - serie 2020

Caldera Vacanza - serie 2020 User Manual - German - 40 pages

Caldera Vacanza - serie 2020 User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info