784918
40
Zoom out
Zoom in
Previous page
1/44
Next page
Page 37
Service Information
GENERAL OPERATION TROUBLESHOOTING GUIDE
Problem Probable causes Solutions
Entire spa is inoperative Power failure
GFCI tripped
Heater high limited thermostat tripped
Spa Lock activated
Check power source
Reset GFCI; call for service if it will not reset.
Disconnect power for at least thirty seconds to reset
heater high limit. If it will not reset, check for clogged
filters. If tripping continues, call for service.
Deactivate Spa Lock
Jets weak or surging Spa water level too low
Filter clogged
Air valves are closed
Add water
Clean filter
Open air valves
Light inoperative Spa Lock activated
Light assembly is faulty
Deactivate Spa Lock
Call for service
Both Power and Ready
Indicators Blinking
Dirty filter
Low water level
Pressure switch problem
Temperature sensor problem
Clean filter
See Start Up section in Owners Manual
Disconnect power for at least thirty seconds. If flashing
continues after power up, call for service
Power Indicator Blinking
with four lines in display
area
Heater high limit thermostat tripped Disconnect power for at least thirty seconds to reset
heater high limit. If it will not reset, check for clogged
filter. If tripping continues, call for service
Ready Indicator Blinking Temperature sensor problem Disconnect power for at least thirty seconds. If blinking
continues after power up, call for service
Spa not heating properly Temperature set too low
Spa cover improperly positioned
Dirty filter
Summer Timer on
Set control panel to a higher temperature.
Align spa cover
Clean filter
Turn summer timer mode to off position
Pump motor will not
function
Motor overload condition
Control switch failure if jet symbol does not come
on
Let cool for one hour. Motor overload will reset
automatically. If problem persists, contact your
CALDERA dealer
Disconnect spa and contact your CALDERA dealer
Noisy pump or motor Low water level Add water to normal level (2.5 cm or 1 inch above
highest jet)
Pump motor runs, but low
or no water/jet pressure
Air control valve closed or blocked
Low water level
Dirty filter cartridge
Jet blocked
Clogged suction or skimmer basket
Open or clean air valve
Add water to normal level (1 inch above highest jet)
Clean filter cartridge
Remove jet face eyeball and clean orifice
Clean suction cover or skimmer basket
Diverter valves are difficult
to turn
Sand or grit inside valves Clean and lubricate valve per diverter valve
maintenance instructions
After filling or refilling
the spa: a jet pump is
operating, but water is not
flowing from any of its jets.
Pump is not properly primed.
Turn off power to the spa at the breaker and remove the
equipment compartment door (see the "Draining Your Spa"
section for illustration).
Loosen the union on the top of the pump(s) (see the
"Winterizing Your Spa" section for illustration) to allow the
air to escape, and then hand-tighten the union(s).
Turn power back on, activate the pump, and check to
make sure the union is tight enough to keep it from leaking.
Replace the equipment doors.
OR: Remove and reinstall the FROG cap.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caldera Paradise - serie 2018 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caldera Paradise - serie 2018 in the language / languages: English as an attachment in your email.

The manual is 5.66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caldera Paradise - serie 2018

Caldera Paradise - serie 2018 User Manual - German - 44 pages

Caldera Paradise - serie 2018 User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info