694404

Cadel Tile3 Plus Manual

30
Zoom out
Zoom in
Previous page
1/48
Next page
30
WALL
3
PLUS - LEAN
3
PLUS - MOON - TILE
3
PLUS
EN
12.8 FAILED IGNITION
If pellets should not ignite, the lack of ignition will be signalled by the A01 "No Ignition" warning.
If the ambient temperature is below 5°C, the resistance may not heat up enough to guarantee the pallet ignition.
In this case, remove the unburned pellets from the burning pot and restart ignition.
• Too much pellets in the burning pot, or humid pellet, or sooty burning pot make ignition difcult and create
dense white smoke which is harmful to health and can cause explosions on the combustion chamber. It is
therefore necessary not to stand in front of the stove during ignition stage if dense white smoke is present.
If after some months the ame appears weak and/or orange colored or the glass tends
to blackens and the burning pot to become encrusted, clean the stove, clean the fume
conduit and the chimney ue.
12.9 SWITCH OFF (ON PANEL: OFF WITH FLASHING FLAME)
If the shutdown key is pressed or if there is an alarm signal, the boiler goes into the thermal shutdown phase which
entails the automatic execution of the following stages:
• Pellet loading is stopped.
• The room fan continues to operate until the requested temperature is reached.
• The ue fan is set to its highest value, which it keeps until the requested temperature is reached, plus a
safety time of 10 additional minutes. After that, if the fume temperature has decreased below the switch off
threshold, it stops, otherwise the cooling process goes on.
• If the stove has switched off normally, but owing to thermal inertia, the fume temperature goes over the
threshold again, the switch off process is reactivated until the temperature decreases again.
12.10 POWER FAILURE
• After a black-out lower than 10 seconds, the stove turns back to the power which was settled.
• After a black-out of more than 10 seconds, the stove enters the during shutdown. Completed this phase, it
starts automatically up with the different phases.
12.11 ADJUSTMENTS MENU
To access the adjustments menu act as follows:
• Press the + - keys
• Scroll with the <> arrows and select “Set Room T ” or “Air Fan Speed 1” or “Air Fan Speed 2” or “Comfort
Mode” or "Fire"
• Press “menu” to access the selected option.
• Modify with the + - keys.
• Press “menu” to conrm and “esc” to exit.
Set Room T. - this function allows setting the desired temperature in the room where the stove is installed, starting
from a minimum of 5°C up to a maximum of 35°C. When this condition is met, the stove reaches the minimum
consumption values (ame and hot air fan speed at minimum values) and then goes back to theset values when
the ambient temperature goes below the set threshold (see ).
Fig. 55 - Display
Note: The full stop to the right of the ambient temperature shown in the control panel display (upper right)
indicates the half degree (e.g. 23.° means 23.5°C).
Air Fan Speed 1 - this function allows selecting the desired speed for the ambient fans from 1 to 5 or A. A means
automatic, ventilation depends on power, recommended setting (see Fig. 56 page 31).
Air Fan Speed 2 - this function allows selecting the desired speed for the DUCTING fans from 1 to 5 or A. A means
automatic, ventilation depends on power, recommended setting (see Fig. 57 page 31).
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cadel Tile3 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cadel Tile3 Plus in the language / languages: English as an attachment in your email.

The manual is 21,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cadel Tile3 Plus

Cadel Tile3 Plus User Manual - German - 48 pages

Cadel Tile3 Plus User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info