815163

Cadel TESIS 16-23 AIRTIGHT Manual

24
Zoom out
Zoom in
Previous page
1/40
Next page
IDROSTUFE
18
10.6 POWER FAILURE
• After a black-out lower than 10 seconds, the stove turns back to the power which was settled.
• After a black-out of more than 10 seconds, the stove enters the during shutdown. Completed this phase, it starts automatically
up with the different phases.
10.7 FAILED IGNITION
If pellets should not ignite, the lack of ignition will be signalled by the A01 "No Ignition" warning.
If the ambient temperature is below 5°C, the resistance may not heat up enough to guarantee the pallet ignition. In this case,
remove the unburned pellets from the burning pot and restart ignition.
• Too much pellets in the burning pot, or humid pellet, or sooty burning pot make ignition difficult and create dense white
smoke which is harmful to health and can cause explosions on the combustion chamber. It is therefore necessary not to stand
in front of the stove during ignition stage if dense white smoke is present.
If after some months the flame appears weak and/or orange colored or the glass tends to blackens and the
burning pot to become encrusted, clean the stove, clean the fume conduit and the chimney flue.
11 RECOMMENDATIONS FOR SAFE USE
ONLY PROPER INSTALLATION AND APPROPRIATELY SERVICING AND CLEANING THE APPLIANCE
CAN ENSURE PROPER OPERATION AND SAFE PRODUCT USE
We wish to inform you that we are aware of cases of malfunctioning domestic pellet heating products, essentially due to improper
installations and inappropriate maintenance.
We wish to ensure you that all our products are extremely safe and certified according to the European reference standards. The
ignition system was tested with extreme care to increase ignition efficiency and prevent any issues even in the worst operating
conditions. In any case, as with any pellet product, our appliances must be installed properly and periodically cleaned and serviced
in order to ensure safe operation. Our research suggests that these malfunctions are essentially due to a combination of part or all
of the following factors:
• Clogged brazier holes or deformed brazier, due to poor maintenance. These conditions can cause delayed ignition, creating an
abnormal production of unburnt gases.
• Insufficient combustion air due to a reduced or clogged air intake duct.
• Using smoke ducts that do not meet the installation standard requirements, such to fail to ensure appropriate draft.
• Partially obstructed chimney due to poor maintenance, such to reduce draft, making ignition difficult.
• Terminal chimney cap not compliant with the instructions manual, thus not suitable to prevent potential backdraft.
• This factor becomes crucial when the product is installed in particularly windy areas, like on the coast.
The combination of one or more of these factors could cause significant malfunctions.
To prevent this from happening, it is essential to ensure the product is installed in compliance with the standards in force.
Furthermore, it is essential to follow these simple rules:
• Every time it is removed for cleaning, the brazier must always be properly repositioned in the work position before using the
product, thoroughly cleaning any residual dirt on the support base.
• Never load pellets into the brazier manually, either before ignition or during operation.
• Any unburnt pellets after a failed ignition must be removed before re-igniting the product. Also make sure it is properly posi-
tioned in its housing and check for normal combustion air intake/smoke extraction.
• If the product repeatedly fails to ignite, we recommend that you stop using it immediately and contact a qualified technician
to check product operation.
Following these instructions is more than enough to ensure normal operation and prevent any issues with the product.
If the above precautions are not respected and there is a pellet overload in the brazier during ignition and subsequent abnormal
smoke generated in the combustion chamber, carefully follow these instructions:
• Do not, for any reason, unplug the product from the electrical mains: this would stop the smoke extraction fan, resulting in
smoke being emitted into the room.
• Pre-emptively open the windows to air any smoke out of the installation room (the chimney may not work normally)
• Do not open the fire door, as this would compromise normal operation of the smoke exhaust system to the chimney.
• Simply switch off the stove using the on/off button on the control panel (not the rear button of the power supply plug!) and
move away from the product as you wait for the smoke to clear completely.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cadel TESIS 16-23 AIRTIGHT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cadel TESIS 16-23 AIRTIGHT in the language / languages: English as an attachment in your email.

The manual is 2.27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info