643389
20
Zoom out
Zoom in
Previous page
1/36
Next page
20
CLOE - CLOE
3
- SQUARE
EN
POS. REFERENCE DESCRIPTION
5
BUZZER MODE
(audio alarm)
Press once P3 key and with P1 and P2 keys put in "OFF" or "ON".
6 INITIAL LOAD
When the stove has its rst ignition, the auger is completely empty. If it should be necessary
do a precharge by pressing P3 key, then P1 key for starting up and P4 key for stop.
7 STOVE STATE
It shows all parameters connected to the stove state: this is a menu for the Authorized
Techinician
8 TECHNICA SETTING Only for the Authorized Technician.
9 FLAME SETTING It enables to set the ame dipending on the draught of the chimney ue.
12.4 START UP
We remind you that the rst ignition must be carried out by a specialized and authorixed technician who will
check that all is installed in compliance with current regulations and checks the efciency.
If inside the combustion chamber there are booklets, manuals, etc..., remove them.
Check if the door is correctly closed.
Check if the stove is correctly inserted in the electric socket.
Before switching the stove on, assure you the burning pot is clean.
To start the stove up, keep pressed P4 key for an instant till it will be shown "START" and "PREHEAT WAIT": the
preheating of the ingnition resistance starts. After 2 minutes about, it will be shown "PELLET LOAD, WAITING FIRE",
in this phase the auger loads the pellet and the heating of the resistance continues. When the temperature is
sufciently high (after 7-10 minutes about), the ignition is considered as happened and on the display shows
"FIRE PRESENT".
Completed the phase "FIRE PRESENT", the control unit enter the "WORK" phase showing the set caloric power
and ambient temperature. It is in this phase that P5 and P6 keys settle the stove power from 1 to 5. If the value
of the ambient temperature exceeds the limit set on the keyboard on the temperature setting, the caloric
power will be carried at the minimum showing "WORK, MODULAT". When the ambient temperature turns
back below the set temperatur, the stove turns back to the set power.
12.5 STOVE ADJUSTMENT
The stove is adjusted according to the chimney ue and used pellets datas, as per technical characteristics (see
FEATURES page 35). If the datas do not correspond, the authorized technician can adjust the stove.
If the pellet is small in size and with a greater caloric power, (for example: encrusted burning pot), the pellet
drop must be decreased from the menu "FLAME SETTING", press P3 "PELLET TYPE", press P3 again "PELLET LOAD"
and with P2 key decrease the pellet quantity from -1 (which is -2%) till -9 (which is -18%).
If the chimney ue has a lower draught (for example: weak ame, sooty glass) the revolutions of the geared
motor must be increased from the menu "FLAME SETTING", press P5 "CHIMNEY TYPE", press P3 "FUME-EXH
CHIMNEY" and with P1 key increase the fume fan revolutions from +1 (which is +5%) till +9 (which is +30%).
If the chimney ue has a greater draught (for example: because of pellets fall on the burning pot) decrease
the fume fan revolutions from -1 to -9.
Pay attention if the value is positive or negative..
12.6 FAILED IGNITION
If the pellets do not burn, the failed ignition will be indicated by the alarm "FAILED IGNITION".
If the room temperature is lower than 10°C, the plug is not able to bear the ignition stage. To support it please
insert some pellets in the burning pot and a piece of burning relighter igniter material on the pellets (for
example relighters cubes).
Too much pellets in the burning pot, or humid pellet, or sooty burning pot make ignition difcult and create
dense white smoke which is harmful to health and can cause explosions on the combustion chamber. It is
therefore necessary not to stand in front of the stove during ignition stage if dense white smoke is present.
If after some months the ame appears weak and/or orange colored or the glass tends
to blackens and the burning pot to become encrusted, clean the stove, clean the fume
conduit and the chimney ue.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cadel SQUARE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cadel SQUARE in the language / languages: English as an attachment in your email.

The manual is 7,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cadel SQUARE

Cadel SQUARE Usermanual and installation guide - German - 40 pages

Cadel SQUARE Usermanual and installation guide - Dutch - 38 pages

Cadel SQUARE Usermanual and installation guide - French - 40 pages

Cadel SQUARE User Manual - Italian, Portuguese, Spanish - 354 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info