696858
39
Zoom out
Zoom in
Previous page
1/72
Next page
IDRO PRINCE
3
12-16-23-23 H
2
O - IDRO PRINCE 30-30 H
2
O - AQUOS
3
16-23-23 H
2
O - IDRON 16-22 AIRTIGHT - MIRA 16-22 -
TESIS 16-23
AIRTIGHT - HIDROFIRE 22.8
39
7.9 WASHING THE SYSTEM
The connections must be easy to disconnect via pipe unions with swivel fittings.
Install suitable gate valves on the heating system pipes. A safety valve must be installed on the system.
To protect the heating system from harmful corrosion, build-ups or deposits, it is extremely important before installing the ap-
pliance to wash the system in compliance with the UNI 8065 standard (water treatment in heating systems for domestic use),
using appropriate products.
7.10 FILLING THE SYSTEM
To fill the system, the stove may be equipped with a terminal (optional) with a non-return valve (D) to manually fill the heating
system (if there is no terminal, use the filling valve on the main boiler). During this operation, the automatic bleed valve under the
top ensures that any air in the system is expelled.
To allow the valve to bleed, we recommend loosening the grey cap by a turn and leaving the red cap tight (see figure). The filling
pressure when the system is COLD must be 1 bar. During operation, should system pressure drop (due to the gas dissolved in the
water evaporating) below the above indicated minimum value, the user must bring it back to the initial value, using the filling valve.
For proper stove operation when it is HOT, pressure in the boiler must be 1.5 bar.
To monitor system pressure, the terminal (optional) is equipped with a pressure gauge (M).
When filling is complete, always shut off the valve.
It is normal for there to be noises and gurgling until all the air in the system has been expelled.
Fig. 45 - Terminal with lling valve (D) and
pressure gauge (M)
Fig. 46 - Manual bleed valve (located under the
top) (Idro Prince
3
16-23-23 H2O, Aquos
3
16-23-23
H2O, Idron 16-22 Airtight, Hidrore 22.8)
Fig. 47 - Manual bleed valve (located under the
top) (Idro Prince
3
30-30 H2O)
7.11 WATER CHARACTERISTICS
The characteristics of the water used to fill the system are very important to prevent the build-up of mineral salts and the forma-
tion of incrustations along the pipes, in the boiler and in the heat exchangers.
Therefore, please ASK YOUR PLUMBER FOR HIS ADVICE CONCERNING:
Hardness of water circulating in the system, to prevent problems of incrustation and limescale, especially in
the domestic water heat exchanger. (> 25° French).
Installation of a water softener (if water hardness exceeds 25° French).
Filling the system with treated water (demineralised).
Possibly providing an anti-condensation circuit.
Installation of hydraulic shock absorbers to prevent water hammering along the fittings and pipes.
If you have very extensive systems (with a large amount of water) or which require frequent refilling, the installation of water
softening systems.
It should be remembered that incrustations drastically reduce performance due to their extremely low thermal
conductivity.
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cadel IDRO PRINCE 30 H2O at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cadel IDRO PRINCE 30 H2O in the language / languages: English as an attachment in your email.

The manual is 2,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cadel IDRO PRINCE 30 H2O

Cadel IDRO PRINCE 30 H2O User Manual - German - 76 pages

Cadel IDRO PRINCE 30 H2O User Manual - Dutch - 72 pages

Cadel IDRO PRINCE 30 H2O User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info