Manual Cadel Ibis 22 H2O (page 44 of 56) (English)

643494

Zoom out

Zoom in

1/56

AQUOS - IBIS - IDRON

14.15 ALARM RESET

To reset the alarm one must press and hold key 1 (ESC) for a few seconds. The boiler performs a check to

determine if the cause of the alarm persists or not.

In the rst case the alarm will still be displayed, in the second case it will go onto OFF.

If the alarm persists, contact the service centre.

14.16 NORMAL SHUTDOWN (ON THE PANEL: OFF WITH FLASHING FLAME)

If the shutdown key is pressed or if there is an alarm signal, the boiler goes into the thermal shutdown phase which

entails the automatic execution of the following stages:

• It stops pellets loading

• The room fan (if provided) maintains the set speed until the smoke T reaches 100°C, then it automatically sets

itself at the minimum speed until it reaches the shutdown temperature

• The smoke fan sets itself at maximum speed and maintains it for a xed time of 10 minutes, at the end of which

if the smoke T has fallen below the shutdown threshold it switches off permanently, otherwise it sets itself at the

minimum speed until it reaches such threshold before switching off.

• If the boiler was shutdown regularly but, due to thermal inertia the smoke temperature exceeds the threshold

again, the shutdown stage restarts at the minimum speed until the temperature goes down.

14.17 BLACKOUT WITH THE BOILER ON

In the event of a power cut (BLACKOUT) the boiler behaves as follows:

• Blackout below 10”: it returns to its operation in progress;

• In the event of a power cut that lasts over 10” with the boiler on or in the start-up stage, when the boiler is

powered again it goes back to the previous operating condition with the following procedure:

1) It cools down activating the smoke extractor at minimum power for 10’ and goes onto the next point;

1) It takes the boiler back to the operating condition before the blackout.

During stage 1 the panel displays ON BLACK OUT.

During stage 2 the panel displays Start-up.

If during stage 1 the boiler receives commands from the panel and thus carried out manually by the user, then

the boiler stops executing the blackout recovery status and proceeds to restart or shutdown as requested by

the command.

14.18 BLACKOUT ABOVE 10” WITH BOILER IN SHUTDOWN STAGE

In the event there is a power cut that lasts MORE THAN 10” with the boiler in the shutdown stage, when the

boiler is powered again it restarts in shutdown mode even if the smoke temperature has fallen under 45°C in the

meanwhile. This last stage can be skipped by pressing key 1 (esc) (it goes into start-up) and by pressing it again

(it recognises that the boiler is switched off).

MAINTENANCE AND CLEANING

Fig. 37 - Example of a clean brazier Fig. 38 - Example of a dirty brazier

ATTENTION!

All the cleaning operations of all parts must be performed with a completely cold product

and the plug disconnected.

The product requires little maintenance if used with certied high quality pellets.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cadel Ibis 22 H2O in the language / languages: English as an attachment in your email.

The manual is 6,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cadel Ibis 22 H2O

Cadel Ibis 22 H2O Usermanual and installation guide - German - 56 pages

Cadel Ibis 22 H2O Usermanual and installation guide - Dutch - 56 pages

Cadel Ibis 22 H2O Usermanual and installation guide - French - 56 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cadel Ibis 22 H2O Manual

Product: