Manual Cadac Safari Chef 30 - 6540H1 (page 5 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish, Norwegian, Finnish)

819980

Zoom out

Zoom in

1/132

3. Connecting the gas supply and operating the appliance

Connecting the gas supply

• Before connecting the appliance to a gas cartridge, ensure that the rubber seals are in position and in good

condition.

• Before connecting the gas cartridge to the appliance, check that the appliance control knob is in the “OFF”

position.

• Carry out this check each time you ﬁt the appliance to a gas cartridge.

• Blow out any dust from the gas supply opening to prevent possible blockage of the jet.

• Ensure that the gas cartridge is ﬁtted in a well-ventilated location away from any source of ignition, such as

naked ﬂames and away from other people.

• Make sure that the gas cartridge is kept upright at all times, connect to the cartridge by screwing on hand

tight until fully engaged.

• Ensure that a complete gas seal has been made (check for the smell of gas around the connection joint). Do

not check for leaks with a naked ﬂame. Use warm soapy water only, applied to the joints and connections of

the appliance. Any leakage will show up as bubbles around the leakage area.

• If you cannot rectify the gas leak do not use the appliance. If you are in doubt, contact your nearest stockist.

Disconnecting and changing the gas supply

• Check that the burner is extinguished before disconnecting the gas cartridge.

• To disconnect the gas cartridge, unscrew the cartridge in a counter clockwise direction from the valve keeping the appliance in vertical

position. (See Fig 4b)

• Check the seal before replacing the gas container (Fig. 4c).

Fig 3

Piezo

Control knobControl knob

Fig 4a Fig 4b Fig 4c

Seal

• When operating this appliance, please take care to ensure that all parts are in good working order and that you have checked for any gas

leaks before lighting the appliance with every use.

• Cooking surfaces can simply be placed and are ready to use. No assembly required.

• PLEASE NOTE: Please ensure all protective packaging and plastic are removed from the appliance before use.

• The appliance is designed for use with cooking vessels of not less than 150mm in diameter and not greater than 300mm in diameter.

Precautions to observe before lighting.

• Use this appliance only on a ﬁrm level surface.

• Aer prolonged storage, inspect the appliance for any insects and webs, which may aﬀect gas ﬂow.

Lighting the appliance using the piezo

• It is recommended to remove any cooking surfaces when trying to light the appliance. This way it will be easy to see the burner when it is lit.

• To light up the appliance using the piezo igniter, push and turn the control knob to its highest setting in an anti-clockwise direction, then

press the piezo button to ignite the gas. If the gas does not ignite on the ﬁrst spark, turn the control knob back to its “OFF” position. Try

again, by pushing and turning the control knob anti-clockwise and push the piezo button to ignite the gas. If the gas has not ignited in the

ﬁrst two to three seconds you should close the control valve by turing the control knob back to its “OFF” position.

• Wait approximately thirty seconds to let any accumulated gas within the burner escape. Repeat the above process if necessary until the

ﬂame ignites. The ﬂame should normally light up within the ﬁrst one to two seconds.

Lighting up using a BBQ lighter

• When starting cold, the appliance may be lit from the top prior to ﬁtting the desired cooking surface. When lighting up a hot appliance, it

is recommended that this be done by sticking a barbecue lighter through one of the vent holes underneath the burner, until it is in line with

the burner (DO NOT place the BBQ lighter through the large hole directly underneath the burner). Ignite the BBQ lighter. Whilst the BBQ

lighter is lit, push and turn the control knob anti-clockwise to light the burner.

General

• Once the appliance is lit, the ﬂame intensity may be adjusted by turning the control knob clockwise to decrease the ﬂame and anti-

clockwise to increase the ﬂame.

• When cooking food with a high fat content, ﬂaring may occur if the selected heat setting is too high. Should this happen, turn the heat down

until the ﬂaring ceases.

• Do not move the appliance when in use. It is unsafe practice to move the appliance whilst lit and may cause ﬂaring.

• Aer use, ensure the control knob on your appliance is in the oﬀ position, and that the ﬂame is extinguished before removing the cartridge.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cadac Safari Chef 30 - 6540H1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cadac Safari Chef 30 - 6540H1 Manual

Product: