684204

Cadac 98501 Manual

4
Zoom out
Zoom in
Previous page
1/6
Next page
2. Safety Information cont.....
3. Using the Appliance
Hang the cylinder from the bracket situated on the side of the BBQ.
Use this appliance only on a firm level surface.
Before use ensure that the drip tray is in place. It is recommended that sand is placed in the drip tray
in order to catch dripping fat and prevent flaring. It will also assist in cleaning after use as the fat will
be easier to remove from the surface of the drip tray.
Never place sawdust or any other combustible material in the drip tray.
Make sure the gas cylinder is correctly fitted to the appliance.
Ensure the cylinder control valve is in the open position.
To light the appliance using the automatic igniter, push in and turn the control knob in an anti-
clockwise direction until spring resistance is felt. Hold the knob in this position for 3 – 5 seconds to
allow the gas to flow and then turn the knob fully anti-clockwise to the ON position. This will cause the
automatic lighter to light the burner. Should the burner not ignite the first time, turn the control knob to
the OFF position and wait 5 minutes before repeat the process until the burner ignites.
Note! All burners are fitted with an automatic igniter.
Cross lighting: To light the burners using cross lighting, light the left burner as described above.
To light the remainder of the burners, simply turn their control knobs to the HIGH position while
ensuring that the lighting sequence is such that any burner to be lit up is directly adjacent to a burner
which is already burning.
Manual ignition: To light the burners manually, first remove the cast iron grill plate and the deflector
plate directly underneath it. Ignite a match or firelighter and position it next to the left hand burner.
Turn on the gas supply to that burner only by pushing the control valve in and turning it in an anti-
clockwise direction. This will ignite the burner. Once the burner is ignited, carefully replace the
deflector plate and cast iron grill plate. You will now be able to light the remainder of the burners as
described in 'Cross lighting' above.
Use the control knobs to adjust the individual burner flame intensity to the desired level by turning the
knob anti-clockwise to decrease the flame and clockwise to increase it (see fig.3). If flaring occurs,
first check that the primary air supply openings in the burner mixing tube are not blocked.
After use, first close the valve on the gas cylinder. When the flame is extinguished, close the burner
control valves on the appliance by turning control knobs fully clockwise.
4. Fitting And Changing The Gas Cylinder
Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the regulator is in
position and in good condition.
Carry out this check each time you fit the appliance to a gas cylinder (see fig. 1).
Blow out any dust from the cylinder opening to prevent possible blockage of the jet.
Hang the cylinder on the Cylinder Bracket situated on the side of the trolley.
Ensure the gas cylinder is fitted or changed in a well ventilated location preferably outdoors, away
from any source of ignition such as naked flames, and away from other people.
Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto the
cylinder until it is fully engaged.
If you wish to check for leaks in your appliance, do it outside. Do not try to detect leaks using a flame. The
correct way is to smear the suspected area with soapy water. If bubbles form, then there is a gas leak.
Immediately turn off the gas supply firstly by closing the control valve on the gas cylinder and then the
appliance valves. Check that all the connections are properly fitted. Re-check with soapy water. If a gas
leak persists return the product to your CADAC dealer for inspection/repair.
Ensure that the gas cylinder is connected or changed in a well ventilated area, preferably outdoors, away
from any source of ignition such as open flames, and away from other people.
Keep gas cylinders away from heat and flames. Do not place on a stove or any other hot surface.
Ensure that the assembled unit is stable and does not rock.
Do not cover or change the primary air supply openings in the burners as this will affect the performance
of the product and may lead to an unstable flame.
In the event of burn back, (where the flame burns back and ignites at the jet), immediately turn off the gas
supply by first closing the control valve on the gas cylinder and then the appliance valve.After the flame is
extinguished remove the regulator and check the condition of its seal. Replace the seal if in doubt. Re-
light the appliance as described in Section 3 below. Should the flame light back persistently return the
product to your authorized CADAC repair agent.
Do not modify the appliance or use it for anything which it has not been designed for.
During use, part of the appliance will become hot, particularly the cooking areas and the hood. Avoid
touching hot parts with your bare hands. The use of oven gloves is recommended.
Keep young children away from the appliance at all times.
This appliance consumes oxygen and needs ventilation for optimum performance and for the safety of
those in close proximity.
Do not move the appliance while in use.
The parts sealed by the manufacturer or its agent must not be altered by the user.
Any modification of the appliance may be dangerous.
Do not twist or pinch the hose. Ensure that it is kept away from the BBQ body so as to prevent
deterioration/damage to the hose caused by heat.
Fit one end of the low pressure hose onto the regulator nozzle, and the other end onto the Patio BBQ
nozzle by pushing the ends on as firmly as possible. Clamp into position using a hose clamp at both ends
of the hose.
Ensure that the connections are made securely and do not allow gas to leak.
Check for gas leaks before using the appliance.
For use with an approved hase and regulator connected to a refillable gas container not exceeding 11kg
and complying with local regulation in force.
NOTE
Fig.1
Fig.2
Fig.3
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cadac 98501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cadac 98501 in the language / languages: English as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cadac 98501

Cadac 98501 User Manual - German - 7 pages

Cadac 98501 User Manual - Dutch - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info