Manual Cadac 8309 - Grill2Braai (page 7 of 9) (English)

684183

Zoom out

Zoom in

1/9

5. ASSEMBLY INSTRUCTIONS

Ÿ Note: The hose and regulator are not supplied. For details contact your local stockist.

Ÿ I 3B/P (30), I 3+ (28-30/37) and I 3B/P (37),

Appliance categories:

(DK, FI, NO, NL, SE, AT, DE, BE, ES, FR, IE, IT, PT, GB, CH)

On the other end, attach a suitable 30mbar low-pressure

(I3B/P (30) : 30mbar Butane/Propane configurations regulator; I3+(28-30/37): 30mbar Butane

regulator or 37mbar Propane regulator); I3B/P(37): 37mbar Butane/Propane configurations

regulators). Again making sure that the hose is well seated. The type of hose used shall

comply with the relevant EN standard and locate requirement. In South Africa the regulator

used must comply with SABS 1237.

Ÿ I 3B/P (50) Appliance category: (AT, DE)

Screw a Hose with the correct threaded fittings on each end, onto the left hand ¼“ BSP

thread of the Valve (O) (Fig.4). Attach a suitable 50mbar low-pressure regulator on the other

end of the hose. The hose used must comply with DIN 4815 part 2 or equivalent.

Ÿ The hose length should be no less than 800mm and shall not exceed 1.5m.

Check the expiry date on the hose and replace when necessary or when national conditions

require it.

Ÿ Do not twist or pinch hose. Do not route the hose in any manner that will cause it to come

into contact with any surfaces that would

become hot during use.

Ÿ Before fitting your gas cylinder ensure (Section 7),

that the Valve (M) is in the OFF position by turning

the Control Knob (K) clockwise to its stop position.

(See Fig.8 a, b)

Ÿ Fit the Burner Pan(F) onto the Stem(H), and ensure

is sealed properly.(Fig 5)

6. FITTING AND CHANGING THE

GAS CONTAINER

Ÿ Before fitting the regulator to a gas container, ensure

that the seal on the regulator is in position and in

good condition. This should be done with every connection.

Ÿ Ensure that the gas container is fitted or changed in a well-ventilated location,

preferably outdoors, away from any source of ignition such as naked flames or

electric fires and away from other people.

Ÿ Making sure that the gas container is kept upright, screw the regulator onto the

container until it is fully engaged. Hand-tighten only.

Ÿ If there is a leak on your appliance (smell of gas), take it outside immediately into a

well-ventilated flame-free location where the leak may be detected and stopped.

If you wish to check for leaks on your appliance, do it outside using soapy water

only, which is applied to the joints. The formation of bubbles will indicate the gas

leak.

Ÿ Check that all the connections are securely fitted and re-check with soapy water.

If you cannot rectify the gas leak, do not use the appliance. Contact your

local CADAC stockist for assistance.

Ÿ When changing a gas container, firstly close the container valve (if fitted) and then

turn the Control Knob (K) clockwise to its stop position. Ensuring that the flame is

extinguished, unscrew the regulator. Refit a full container following the same

precautions as described above.

Fig. 3

Fig. 5

Fig. 4

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cadac 8309 - Grill2Braai in the language / languages: English as an attachment in your email.

The manual is 1,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cadac 8309 - Grill2Braai

Cadac 8309 - Grill2Braai User Manual - German - 10 pages

Cadac 8309 - Grill2Braai User Manual - Dutch - 10 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cadac 8309 - Grill2Braai Manual

Product: