The pot stands and aluminium grill plates can be used in any configuration (i.e. one pot stand and one grill, two grills or two pot stands).
After lighting, do not move the gas cylinder and the appliance around, as liquefied gas may enter the appliance from the gas cylinder, causing it to
flare (large yellow flames).
Always operate the appliance on a firm level surface with the gas cylinder in an upright position.
Turn the control knob clockwise to the 'OFF' position.
Turn the gas supply 'ON' at the cylinder.
Turn the control knob anti-clockwise until a hissing sound is heard, press the piezo button. This should ignite the burner.
If the burner does not stay alight, repeat as above.
To turn the stove 'OFF', turn the cylinder valve to the 'OFF' position and then turn the control knob on the appliance clockwise to the‘OFF' position.
To light the appliance, ignite a match or barbecue lighter, turn ON the appliance valve after connecting to and opening the cylinder valve, by turning
the control knob in an anti-clockwise direction. Light the appliance burner.
Use the control knob to adjust the flame intensity to the desired level by turning the knob clockwise to decrease the flame and anti-clockwise to
increase it (See Fig. 3).
After use, close valve on gas cylinder. When the flame has extinguished close the valve on the appliance by turning knob fully clockwise.
It is dangerous to use an appliance with a cracked or perished seal and / or tubing. Inspect both seals and tubing regularly and replace if they are
not in order, before using the appliance.
If the appliance was in use, it will be hot.Allow to cool sufficiently before attempting any maintenance.
The stove is fitted with jets to regulate the correct amount of gas.
Should the hole in the jet become blocked this may result in a small flame or no flame at all. Do not attempt to clean the jet with a pin or other such
device as this may damage the orifice, which could make the appliance unsafe.
Ensure that the cylinder valve is closed, and then disconnect the appliance from the gas cylinder.
Remove the self tapping screw which holds the venturi in place.
Move the burner assembly back slightly so as to expose the valve and the jet.
Unscrew the blocked jet with a suitable spanner and replace it with a new jet.
Do not over tighten as this may damage the jet. To re-assemble, reverse the above procedure.
Do not use pliers on the jet as this may damage the jet making it unusable or impossible to remove.
Fitting of a hose is described in Section 4.
to give a gas tight seal.An overfilled gas cylinder can also cause large yellow flames. The cylinder should be returned to filling station and checked
by weight.
Check that the inlet to the venturi is clear and free of obstructions.
If the flame power drops or the gas will not light, check that the gas cylinder still contains gas (shake to hear the noise made by the liquefied gas). If
there is still gas, the jet might have become blocked or partially blocked.
If you suspect a blocked jet, follow the instructions above.
To clean the stove body, simply wipe with a damp cloth using a little detergent, if necessary.
DO NOT IMMERSE INWATER as this will allow water to get into the mixing tube causing the appliance to malfunction.
Do not use abrasive cleaners or scourers as this will cause permanent damage to the painted surface.
To avoid ignition failure, keep the burners clean.
Lighting theAppliance using the Piezo (NotApplicable to Model 186F& 187F)
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Cadac 184F at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Cadac 184F in the language / languages: English as an attachment in your email.
The manual is 0,52 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
