Manual Bushnell 70-0101 (page 5 of 51) (English, German, French, Italian, Portuguese, Spanish)

481960

Zoom out

Zoom in

1/51

COUNTDOWN TIMER ALARM

Countdown / Reverse-Timer Mode

Press MODE button until Countdown Timer Mode is displayed,

represented by ‘RT’ (reverse timer). To operate press

COMP/+

button to start and press again to stop, then press BARO/- button

to reset the Countdown Timer.

To set the Countdown Timer press and hold down

ADJ button for

3 seconds, which will cause the seconds setting to blink. Adjust with

the

COMP/+ or BARO/- button, and then press MODE button to

adjust next setting. Press

ADJ button to save settings and exit. Press

ALTI for ‘AUTO’ to allow Countdown Timer to repeat function

automatically, and press

ALTI again to turn off ‘AUTO’ function.

Press any button when alarm sounds to stop the Countdown Timer.

If nothing is pressed the Countdown Timer will stop beeping after

10 seconds, but the countdown timer will continue if the ‘AUTO’

function is on. To stop the Countdown Timer if the ‘Auto’ function

is on, you must go to the Countdown Timer Mode and press

COMP/+ to turn off the ‘AUTO’ function and then press ALTI

button to stop it.

DIGITAL COMPASS

Compass Mode

Press MODE button until Time Mode is displayed, and then press

COMP/+ button. If already in Time Mode, simply press COMP/+

button and Compass Mode is displayed. Hold the compass level using

the bubble level to get a reading. If the Cardinal Points blink then the

compass may need to be calibrated. (See trouble shooting tips.)

Compass Calibration

In Compass Mode, hold down ADJ button for 3 seconds.

Calibration Mode is displayed. Put the compass on a level, non-

magnetic surface and press the

COMP/+ button. The word CAL

will start blinking. Then, rotate the compass 2 full circles slowly

WHILE HOLDING THE COMPASS LEVEL. Each revolution

should take about 10 seconds. When done, press

COMP/+ again.

When completed, the display shows ‘DONE’ and it will then go

Altitude Alarm

Sets the alarm to sound when the altitude reaches the programmed

level. In the Alarm Mode, the Altitude alarm uses the same

measurement units that were last set in the Altimeter Mode. To

change this you must first change it in the Altimeter Mode. To adjust

the altitude at which the alarm will go off, press

ADJ to enter the

setting mode. Press the

COMP/+ or BARO/- to change the

altitude alarm setting. Press

ADJ to save and exit.

Beep Function

In the Alarm Mode a Beep function is also available. When

activated, the Beep function causes a beep sound to be made

whenever a button is depressed, even when the Alarm function is

turned off. To activate the function go to the Beep function in the

Alarm Mode, press the

ALTI button and ‘ON’ is displayed. Press

again and ‘OFF’ is displayed.

Stopwatch Mode

Press MODE button until Stop Watch Mode is displayed. To

operate, press

COMP/+ button to start and press again to stop.

Pressing

BARO/- button will reset the Stop Watch.

Stop Watch Mode / Split Timing Function

For split timing function, press the BARO/- button while the Stop

Watch is operating in order to stop the display and press again to

continue. The display will show your time down to 1/100th of a

second. You can also press the

BARO/- button while the Stop

Watch is operating to stop the display and then press the

COMP/+

button to stop the Stop Watch and display the final reading. Press

the

BARO/- button again to reset the Stop Watch. Split timing

function is displayed as ‘SPL’ when activated and the display returns

to normal when

BARO/- button is pressed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bushnell 70-0101 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bushnell 70-0101 Manual

Product: