632438
9
Zoom out
Zoom in
Previous page
1/16
Next page
Using Adjustable Seat (Encore)
Loosen tension on upper strap behind seat.
Using Seat Recliner (d’lite, Solo)
For added comfort when children are sleeping, make the
following adjustments to recline seat:
1. Loosen tension on lower horizontal strap on seat back.
2. Loosen tension on helmet pocket straps on upper back of
seat. PHOTO 7
3. To return seat to upright position, reverse steps 1 & 2, and
make sure upper seat strap is also tightened securely.
Hitching Trailer to Your Bicycle
Note: The Burley Forged Standard Hitch is used
for bicycles with either nutted axles
FIGURE 10 or
quick release assemblies.
FIGURES 11 & 12
1. Remove axle nut or rear quick release lever
assembly from bike.
2. Match hole on flat side of hitch upper arm to left (non-
chain ring side) rear dropout hole, and place hitch flat
against the dropout.
3. Loosely reassemble axle nut or quick release assembly
through hitch, dropout and wheel. Racks, bags, or fittings
should not interfere with hitch.
4. Slide flex connector between hitch side arms, and match
holes.
5. Open retaining pin and insert through hitch and flex
connector holes from above. Close retaining pin.
6. Tighten axle nut or tighten and close quick release lever,
with lever pointing to rear of bike. A properly adjusted
quick release lever should leave an imprint on your palm
when the lever is rotated to the closed position. Verify that
hitch is secure and cannot be rotated by hand.
7. Wrap safety strap twice around inside of chain stay. Fasten
hook to D-ring on underside of tow bar end. FIGURE 12
8. To remove trailer from bicycle, unfasten clip from D-ring
and remove retaining pin.
PHOTO 7
FIGURE 12
B U R L E Y D ’ L I T E , E N C O R E A N D S O L O O W N E R S I N S T R U C T I O N A N D S A F E T Y M A N U A L 9
IMPORTANT
UPPER SEAT STRAP SHOULD ALWAYS BE TIGHTENED
BEFORE TRAILERING.
QUICK RELEASE LEVER MUST BE IN CLOSED POSITION AND
HITCH SAFETY STRAP PROPERLY INSTALLED. NUTTED AXLES
MUST BE TIGHTENED SECURELY. HITCH MUST NOT INTERFERE
WITH RACKS, BAGS OR FITTINGS. INSPECT HITCH AND TOW BAR
FREQUENTLY FOR DAMAGE OR LOOSE FASTENERS. DAMAGED OR
IMPROPERLY INSTALLED HITCHES OR INTERFERING PARTS CAN
CAUSE ACCIDENTS RESULTING IN SERIOUS INJURY.
WARNING
Tighten to
return seat
to upright
position
Loosen for
Reclining
Quick Release Lever
Hitch Upper Arm
Retaining Pin
Flex Connector
Hook fastened to
D-ring under tow bar
FIGURE 11: Quick release assemblyFIGURE 10: Nutted axle assembly
Hitch
Nut
Hitch
Nut
Quick Release
Safety strap
wrapped twice
around chainstay
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Burley Solo 2009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Burley Solo 2009 in the language / languages: English as an attachment in your email.

The manual is 4,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info