632456
7
Zoom out
Zoom in
Previous page
1/15
Next page
12 B U R L E Y T R A I L E R O W N E R S I N S T R U C T I O N A N D S A F E T Y M A N U A L
B U R L E Y T R A I L E R O W N E R S I N S T R U C T I O N A N D S A F E T Y M A N U A L 13
Attaching the Handle
d’Lite
, Encore
, Solo
, Lady Bug
, Cub
(Bee
: no handle)
Your trailer comes with a handle which allows for easier maneuvering of the
trailer when it’s not attached to your bicycle. The handle is also an important
part of the optional Burley Jogger Kit
and the optional Burley Stroller Kit
,
which are available at your Authorized Burley Dealer.
To install the handle, slide it into the lower handle bar receivers and tighten
the knobs. (The upper handlebar receivers have spacers in them for the
optional Burley Rollbar, available from your Burley dealer.) To change the
position, remove the handle from the handle bar receivers, flip it over and
reinstall it as described above.
Installing the Cub
Parking Brake
The trailer should be fully unfolded and the tongue removed.
1. Put the trailer on its nose on the floor with the roll cage leaning against
a wall or table. Sort the contents of the hardware bag.
2. Facing the underside of the bucket, locate the rear row of six molded
depressions (see illustration). Holes are drilled in the first, third and
sixth depressions (numbered from the left). See illustration.
3. Put a spring washer and then a fender washer on a mounting screw.
Repeat for the other two screws.
4. Place the brass center post of the brake assembly in the number 3
depression so that the black vinyl grip on the brake handle clears the
rear of the bucket. Let the brake arms hang down. Hold the center post
and screw it into place with a Phillips screwdriver.
5. Reach inside the bucket and thread the screw/spring washer/fender
washer stack through the punched hole and into the brake assembly
center post. Don’t tighten it yet.
6. Swing each of the two brake assembly arms into place in turn, so their
posts enter their respective depressions, and fasten them from the
inside of the bucket with the screw/spring washer/fender stacks.
7. Using two screwdrivers, one inside the bucket and one outside, tighten
the mounting screws firmly, until the spring washers are fully flattened
between the mounting screw heads and fender washers.
8. Take care to keep the far left post
from rotating as you tighten its mounting
screw so that the brake return spring
does not distort.
Handlebar
Flag
Rollbar
Accessory
(optional)
Flag Installation
Hole
Knob
Handlebar
Installation
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Burley Solo 2007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Burley Solo 2007 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info