Manual Burley Nomad 2007 (page 5 of 11) (English)

632536

Zoom out

Zoom in

1/11

8 B U R L E Y T R A I L E R O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L

B U R L E Y T R A I L E R O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L 9

All four side panel hold-downs must be snapped in place before using the

trailer. Otherwise, the side rails can shift or collapse, resulting in the loss of cargo.

WARNING

Installing the Tailgate and Splashguard

Nomad

™

: Thread the rear tie-down straps through the inner and then outer

slots of the male buckle sections of the rear side release buckles, which

are attached to the female buckle

sections on the inside rear of the

side panels. Allow enough slack so

you can loop the webbing straps

over the rear of the side panels. To

attach the front splashguard to the

front of the side panels, repeat this

step using the front tie-down straps

and the front side release buckles.

To accommodate different sizes of

cargo, tighten or loosen the web-

bing straps as required (see illus-

tration).

Installing the Roll Bar

and Cover

Nomad

™

: Place the cover, right side out, over the side rails with the

“Nomad” logo at the front of the trailer. Slip a roll bar knob through one of

the grommets on the cover. Slide the

roll bar through the casing in the top

of the mesh divider. Align one end

of the roll bar with its corresponding

hole on the side rail. Thread the

roll bar knob through one side rail,

and tighten it into the roll bar (see

illustration). Repeat this step for the

roll bar knob on the other side. Pull

the B-tabs down and loop the rubber

O-rings over the trailer frame. Make

sure the cover extends over the top

of each side panel.

Installing the Tongue for

the Nomad

™

Tip the trailer onto its back end.

Slide the tongue onto the pivot

pin at the left front. Remove

the hairpin cotter and lock pin

from the front tongue receptacle,

rotate the tongue up into place,

and snap it into the two plastic

tongue receptacles. Push the lock

pin fully into the front tongue

receptacle. Rotate the lock pin

and locate the hole in it, between

the receptacle and the trailer

frame. Anchor the lock pin by

inserting the hairpin cotter all the

way into the hole in the lock pin.

Never operate the Nomad

™

trailer without tongue lock pin and hairpin

cotter locked in place. An unlocked tongue can loosen or detach and

cause an accident, resulting in serious injury.

WARNING

Installing the Tongue for the Flatbed

™

Rotate the tongue up into the plastic tongue

receptacle at the front frame. To lock the

tongue in place, slip the retaining pin

through the hole in the tongue receptacle

and close the pin (see illustration).

B-tab

Tailgate

Splashguard

Trailer Frame

3. Anchor Lock Pin

with Hairpin Cotter

4. Anchor Lock

Pin with

Hairpin Cotter

1. Slide

Tongue

onto

Pivot Pin

2. Rotate Tongue

into Place

5. Lock Pin and Hairpin

Cotter Locked in Place

(viewed from underside)

The retaining pin must be locked

in place before using the Flatbed

™

trailer; otherwise, the tongue could

shift and cause an accident and

serious injury.

WARNING

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Burley Nomad 2007 in the language / languages: English as an attachment in your email.

The manual is 0,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Burley Nomad 2007 Manual

Product: