632433
9
Zoom out
Zoom in
Previous page
1/12
Next page
Hitching Trailer to Your Bicycle
Note: The Burley Forged Standard Hitch is used
for bicycles with either nutted axles
FIGURE 10 or
quick release assemblies
FIGURES 11 & 12
1. Remove axle nut or rear quick release lever
assembly from bike.
2. Match hole on flat side of hitch upper arm to left (non-chain ring
side) rear dropout hole, and place hitch flat against the dropout.
3. Loosely reassemble axle nut or quick release assembly through
hitch, dropout and wheel. Racks, bags, or fittings should not
interfere with hitch.
4. Slide flex connector between hitch side arms, and match holes.
5. Open retaining pin and insert through hitch and flex connector
holes from above. Close retaining pin.
6. Tighten axle nut or tighten and close quick release lever, with lever
pointing to rear of bike. A properly adjusted quick release lever
should leave an imprint on your palm when the lever is rotated
to the closed position. Verify that hitch is secure and cannot be
rotated by hand.
7. Wrap safety strap twice around inside of chain stay. Fasten hook
to D-ring on underside of tow bar end.
FIGURE 12
8. To remove trailer from bicycle, unfasten clip from D-ring and
remove retaining pin.
FIGURE 12: Forged hitch shown
FIGURE 11: Quick release assembly
FIGURE 10: Nutted axle assembly
B U R L E Y H O N E Y B E E O W N E R S I N S T R U C T I O N A N D S A F E T Y M A N U A L 9
QUICK RELEASE LEVER MUST BE IN CLOSED POSITION AND
HITCH SAFETY STRAP PROPERLY INSTALLED. NUTTED AXLES
MUST BE TIGHTENED SECURELY. HITCH MUST NOT INTERFERE
WITH RACKS, BAGS OR FITTINGS. INSPECT HITCH AND TOW BAR
FREQUENTLY FOR DAMAGE OR LOOSE FASTENERS. DAMAGED OR
IMPROPERLY INSTALLED HITCHES OR INTERFERING PARTS CAN
CAUSE ACCIDENTS RESULTING IN SERIOUS INJURY.
WARNING
Quick Release Lever
Hitch Upper Arm
Retaining Pin
Flex Connector
Hook fastened to
D-ring under tow bar
Hitch
Nut
Hitch
Quick Release
Nut
Safety strap
wrapped twice
around chainstay
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Burley Honey Bee - 2009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Burley Honey Bee - 2009 in the language / languages: English as an attachment in your email.

The manual is 2,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info