632454

Burley Encore 2007 Manual

10
Zoom out
Zoom in
Previous page
1/15
Next page
18 B U R L E Y T R A I L E R O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L
B U R L E Y T R A I L E R O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L 19
Two Passengers, All Models (Except Solo
™
):
For two children, use both shoulder harnesses and two outer crotch straps.
1. If your trailer was set up for single-child use, reverse the process above in
the Single Passenger section. Set up the restraint system for two children,
with the male portion of each Y-buckle facing the center of each
seating position.
2. Attach the center support strap with the O-ring.
3. Seat the first child on one side of
the trailer.
4. Snap shoulder straps into the Y-buckle,
with the buckle positioned at the child’s
sternum.
5. Make sure the shoulder straps are adjusted
so that the child cannot move too far
forward in the seat.
6. Repeat for the second child.
7. Fasten and adjust both lap belts so they
are snug.
Child and cyclist must wear helmets when trailering. Helmets
can prevent or significantly reduce head injury in event of accident.
The junction of Y-buckle must be positioned at child’s sternum to work
correctly. Belts or buckles positioned near your child’s neck can cause
discomfort or serious injury. Check child periodically to ensure that
he/she has not slipped from correct seated position.
WARNING
Hitching your Burley to Your Bicycle
The Burley standard trailer hitch was designed to quickly and safely attach
to virtually all types of bicycles. It is attached to the left rear dropout (the
non-chainring side) of your bicycle.
1. Remove the quick release lever assembly from your bike and set it aside.
2. Line up the hole on the flat side of the hitch upper arm with the left
rear dropout hole.
3. Reassemble the quick release assembly through the hitch and dropout,
but don’t tighten it yet.
4. Slide the hitch receiver end of the tongue between the two hitch side
arms, and line up the holes. The hitch should clear any racks, bags, or
fittings you have on your bicycle. If there is any interference, contact
your Authorized Burley Dealer.
5. Open the retaining pin and insert the pin through the holes.
6. Rotate the pin’s spring clip and close the pin.
7. Now tighten the quick release lever, with the lever pointing to the rear
of the bike. When properly adjusted, you will feel resistance halfway
through tightening the lever (when the lever is pointing straight out
away from the bike).
8. Wrap the safety strap around the inside of the chain stay twice and then
over the hitch body. Fasten the hook to the D-ring on the underside of
the tongue end.
The quick release lever must be in
the closed position. Do not operate
the trailer without the hitch safety
strap properly installed. A dangling
safety strap can contact spokes
and damage the rear wheel or
cause an accident resulting in
serious injury. The hitch must
not interfere with racks, bags,
or fittings. Inspect the hitch and
tongue frequently for damage or
loose fasteners. Interfering parts
or damaged hitch can cause an
accident resulting in serious injury.
WARNING
Safety strap wrapped
around chainstay
Hook fastened to
D-ring under tongue
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Burley Encore 2007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Burley Encore 2007 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info