632526
4
Zoom out
Zoom in
Previous page
1/12
Next page
Installing and Using Parking Brake
1. Tilt trailer onto its nose and lean it against a wall.
2. Place brake assembly’s center post in hole #3 in bucket
bottom. Handle grip must clear bucket. Let brake
arms hang down. Hold center post and screw it into
place. FIGURE 1
3. Place a spring washer and fender washer on each
mounting screw. From inside of bucket, loosely thread
screw/spring washer/flat washer stack through hole and
into brake assembly center post. Do not tighten at
this point.
4. Line up brake assembly arms with outer holes #1 and #6,
and using screw/spring washer/flat washers, fasten them
from inside of bucket.
5. Using one tool on inside of bucket and one on outside,
tighten screws firmly until spring washers are fully
flattened between screw heads and flat washers. To
prevent brake return spring from distorting, use care when
tightening left screw.
6. Engage parking brake by pushing handle to the right.
Exercise caution when disengaging brake, as it may spring
to the left.
Opening and Closing Your Trailer
1. Rotate front tube upward and rear tube back until they
meet on plastic saddles. FIGURE 2
2. Rotate frame locks and snap onto rear tube. FIGURE 3
3. To close trailer, unclip seat buckles on back of seat and
reverse opening process.
To view a video clip of “Opening and Closing Your
Trailer” go to: www.burley.com/support/tutorials.cfm.
FIGURE 2
FIGURE 3
FIGURE 1: Rear underside of trailer
4 B U R L E Y C U B O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L
CHECK THAT THE FRAME LOCKS ARE PROPERLY ENGAGED
BEFORE USING THE TRAILER. FAILURE TO DO SO CAN RESULT IN
SERIOUS INJURY.
WARNING
TRAILERS CAN TIP OVER, CAUSING DAMAGE TO TRAILER AND
SERIOUS INJURY TO PASSENGERS. AVOID CAUSES OF TIP OVER,
ESPECIALLY:
• CHILDREN LEANING OR BOUNCING
HITTING POTHOLES, CURBS, OTHER ROAD OBSTRUCTIONS
TAKING TURNS TOO FAST
• SUDDEN SWERVING
• IMPROPER WHEEL INSTALLATION OR TIRE INFLATION
WARNING
Frame Locks
Front
Rear
Plastic Saddles
Screws/Spring
Washers/Flat
Washers
Brake
Engaged
Brake
Released
Center
Post
1
2
3
4
5
6
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Burley Cub 2009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Burley Cub 2009 in the language / languages: English as an attachment in your email.

The manual is 3,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info