779937
39
Zoom out
Zoom in
Previous page
1/105
Next page
MY20B05-42_1.0_18.07.2019 38
Assembly
Push in the quick release until you hear a
clicking sound. Make sure that the flange is
extended.
Figure 37: Pushing the quick release in
Adjust the clamping with a half-open clamping
lever until the flange reaches the fork end.
Figure 38: Adjusting the clamping
Fully close the quick release. Check the quick
release to ensure it is firmly in place and adjust
on the flange if necessary.
The lever is secured.
Figure 39: Closing the quick release
5.3.4 Installing the wheel in the FOX fork
Only applies to pedelecs with this equipment
5.3.4.1 Wheel with quick release (15 mm)
The procedure for installing the 15 x 100 mm and
15 x 110 mm quick releases is the same.
Place the front wheel in the fork ends of the
fork. Push the axle through the fork end on the
non-drive side and hub.
Figure 40: Pushing the quick release in
Open the axle lever.
Turn the axle five to six complete revolutions
clockwise into the axle nut.
Close the quick release lever. The lever must
be tensioned to the point that it leaves a mark
on your hand.
The lever must be 1 to 20 mm ahead of the fork
leg in the closed position.
Figure 41: Spacing between lever and fork leg
If the lever is tensioned too little or too much
when closed in the recommended position
(1 to 20 mm ahead of the fork), the quick
release must be adjusted.
1-20 mm
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bulls Ebikes Shimano 6100 - 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bulls Ebikes Shimano 6100 - 2020 in the language / languages: English as an attachment in your email.

The manual is 11.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bulls Ebikes Shimano 6100 - 2020

Bulls Ebikes Shimano 6100 - 2020 User Manual - German - 106 pages

Bulls Ebikes Shimano 6100 - 2020 User Manual - Dutch - 107 pages

Bulls Ebikes Shimano 6100 - 2020 User Manual - French - 108 pages

Bulls Ebikes Shimano 6100 - 2020 User Manual - Italian - 110 pages

Bulls Ebikes Shimano 6100 - 2020 User Manual - Spanish - 111 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info