779874
40
Zoom out
Zoom in
Previous page
1/113
Next page
MY21B01 - 12_1.0_06.07.2020 40
Assembly
5.4 Commissioning
Only trained specialist staff may perform initial
commissioning since initial commissioning of the
pedelec requires special tools and specialist
knowledge.
Experience has shown that a pedelec which has
not yet been sold is automatically handed to
customers as soon as it appears ready to ride.
For this reason, every pedelec must be
prepared, so it is fully ready for use
immediately after being assembled.
The assembly report (see Section 11.2)
describes all safety-relevant inspections, tests
and maintenance tasks for the bicycle in a
separate list. All assembly work must be
completed to ensure the pedelec is ready to
ride.
Complete an assembly report for quality
assurance purposes.
5.4.1 Installing the wheel in the Suntour
fork
5.4.1.1 Screw-on axle (15 mm)
Only applies to Suntour forks with 15 mm screw-on axle
1Insert the axle completely on the drive side.
Figure 28: Fully inserting the axle
2Tighten the axle to 8–10 Nm with a 5 mm
hexagon socket spanner.
Figure 29: Tightening the axle
3Insert the securing screw on the non-drive
side.
Figure 30: Pushing the quick release lever into the axle
Burns from hot drive
The drive cooler can become extremely hot
during use. Touching it may cause burns.
Leave the drive unit to cool before assembly.
CAUTION
!
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bulls Cross Rider EVO - BOSCH Intuvia 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bulls Cross Rider EVO - BOSCH Intuvia 2021 in the language / languages: English as an attachment in your email.

The manual is 16.61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bulls Cross Rider EVO - BOSCH Intuvia 2021

Bulls Cross Rider EVO - BOSCH Intuvia 2021 User Manual - German - 118 pages

Bulls Cross Rider EVO - BOSCH Intuvia 2021 User Manual - Dutch - 113 pages

Bulls Cross Rider EVO - BOSCH Intuvia 2021 User Manual - French - 119 pages

Bulls Cross Rider EVO - BOSCH Intuvia 2021 User Manual - Italian - 117 pages

Bulls Cross Rider EVO - BOSCH Intuvia 2021 User Manual - Spanish - 117 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info