779878
89
Zoom out
Zoom in
Previous page
1/124
Next page
MY20B01-12_1.0_12.06.2019 89
Operation
6.14.2 Using a hub gear
Only applies to pedelecs with this equipment
.
Figure 85: Example; Shimano Nexus gear shift: twist
grip (1) for the hub gear with its screen (3), the direction of
rotation to switch up a gear (2) and the direction of
rotation to switch down a gear (4)
Turn the twist grip.
The gear shift switches the gear.
The number on the screen display shows the
changed gear.
6.14.3 Use eShift
eShift refers to the integration of electronic gear
shift systems into the pedelec system.
6.14.3.1 eShift with Shimano DI2 automatic
hub gears
Only applies to pedelecs with this equipment
You can operate the automatic Shimano DI2 hub
gears in manual mode or automatic mode. You
used the gear shift to change gears in manual
mode. In automatic mode, the shift system
changes gear automatically depending on the
speed, pedalling power and pedalling frequency.
You will find how to switch from automatic to
manual mode, depending on the shifter used,
described in your operating instructions for your
gear shift.
If you use the shifter when in automatic mode, the
gear system will change to the next gear, but it will
remain in automatic mode.
Manual gear changes in automatic mode
influence shift behaviour in your gear system and
adjust gear changes to your riding performance
since it is a self-learning system.
If the system is switched on for the first time when
a new, unused wheel is used, the system will learn
the gears first. To do so, the automatic system
changes to the highest/most difficult gear and
then switches through all gears during the first
ride. The new gear is shown briefly on the screen
each time it is changed.
Since the drive unit detects the gear shift and
consequently reduces motor assistance briefly, it
is also possible to switch gears under load or on
hills.
If the pedelec is brought to a halt from a speed
greater than 10 km, the system can automatically
switch back to a pre-set START GEAR.
You can set the START GEAR in the system
settings.
Crash caused by incorrect use
If the rider applies too much pressure on the pedals
during a gear change and activates the shifter or
changes several gears at a time, their feet may slip
from the pedals. As a result, the pedelec may flip
over or fall, which may cause injury.
Switching down several gears to a low gear may
cause the twist grip outer sleeve to suddenly come
off. This will not have an adverse effect on the twist
grip's correct functioning since the outer guide
returns to its original position after the gear change
is complete.
Apply little pressure on the pedals while changing
gears.
Never change more than one gear at a time.
Notice
The interior hub is not completely waterproof. If
water gets into the hub, it may rust and the gear
switch function may no longer function as a result.
Never use the pedelec in places where water
may get into the hub.
In rare cases, noises may be heard from the rear
derailleur in the hub interior after a gear change.
This is normal when gears are changed.
Do not detach the hub. If you need to detach it,
contact your dealer.
CAUTION
!
1
2
3
4
89


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bulls Cross Rider Evo - Bosch Intuvia 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bulls Cross Rider Evo - Bosch Intuvia 2020 in the language / languages: English as an attachment in your email.

The manual is 18.34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bulls Cross Rider Evo - Bosch Intuvia 2020

Bulls Cross Rider Evo - Bosch Intuvia 2020 User Manual - German - 123 pages

Bulls Cross Rider Evo - Bosch Intuvia 2020 User Manual - Dutch - 126 pages

Bulls Cross Rider Evo - Bosch Intuvia 2020 User Manual - French - 129 pages

Bulls Cross Rider Evo - Bosch Intuvia 2020 User Manual - Italian - 128 pages

Bulls Cross Rider Evo - Bosch Intuvia 2020 User Manual - Spanish - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info