678318
106
Zoom out
Zoom in
Previous page
1/117
Next page
LCD Message Description Corrective Action
HDx Error E16
HDx Not Found
Unable to find the drive.
The drive may be disconnected or may have
failed. After shutting down, reinstall the hard
drive.
HDx Broken E30
Replace the DISK
An error occurred, so the drive was
removed from the RAID volume.
Replace the drive. For the replacement
method, refer to the “Hard Drive
Replacement Procedure section in chapter 5.
SYSTEM I10
TOO HOT !
A rise in the system temperature
may have exceeded the allowable
safety value.
Move the TeraStation to a cool location. Do
not place objects in the area around the
TeraStation.
HDx Warning I11
Bad Sectors
The drive has too many bad sectors. Replace the drive.
Operation I12
DEGRADE MODE
Operating in degraded mode.
Check if the E30 message is also displayed
on the LCD panel. In such a case, refer to the
corrective action for the E30 message. If only
this message is displayed, refer to the “I12
Message Appears Despite No Drive Errors
section below.
RAID I18
X Drive Rebuilding
Rebuilding the RAID volume.
Note: Transfer speeds are slower
during the rebuilding process.
Wait until the RAID resynchronization
finishes. It will take about 8–12 hours per
terabyte for a RAID 5 volume and 3–6 hours
per terabyte for a mirrored volume. This
message will disappear when the RAID
resynchronization finishes.
Replication I33
Replicate Failure
An error occurred during
replication.
From Buffalo Replication, click Sync to
execute resynchronization. If the error is
displayed again, contact Buffalo technical
support for assistance.
New Firmware I52
Available
A new firmware version has been
released.
Update the firmware.
I54
Backup Failure
The backup job failed.
Make sure that the backup job is configured
correctly. Make sure that the NAS is on and
not in standby mode. If the backup job still
fails, check the status of NAS, network, and
backup source and destinations. Also, check
the backup log to see if any errors were
recorded.
Default Settings
Administrators Name Administrator
Password password
Shared Folders
Drives C and D are configured as administrative hidden shares
by Windows Storage Server’s default settings.
DHCP Client
Normally, the TeraStation will get its IP address automatically
from a DHCP server on the network. If no DHCP server is
available, then an IP address will be assigned as follows:
IP Address: IP address will be assigned starting from “169.254”.
Subnet Mask: 255.255.0.0
Registered Groups Windows Storage Server’s default groups are registered.
Microsoft Network Group Setting WORKGROUP
105
106


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Buffalo TeraStation WS5200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Buffalo TeraStation WS5200 in the language / languages: English as an attachment in your email.

The manual is 7,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Buffalo TeraStation WS5200

Buffalo TeraStation WS5200 User Manual - German - 122 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info