784867
7
Zoom out
Zoom in
Previous page
1/40
Next page
AVOIDING THE RISK
OF ELECTROCUTION
DANGER - RISK
OF ELECTROCUTION
Initial safety warnings
The hot tub must be powered through
a residual current device (rCD) with a
current release not exceeding 30mA.
The devices and parts which contain
active parts – except those which are
powered from protective extralow
voltage not exceeding 12V – must be
inaccessible from the hot tub.
Connect only to a grounded source.
Do not bury the power cord. A buried
power cord may result in death, or seri-
ous personal injury due to electrocution
if direct burial-type cable is not used, or
if improper digging occurs.
WA R N I NG
• To reduce the risk of electrical shock, re-
place a damaged cord immediately. Fail-
ure to do so may result in death or serious
personal injury due to electrocution.
• Your hot tub must be connected to a
Ground Fault Circuit Interrupter (GFCI)
for user and equipment protection. To
ensure proper operation of this import-
ant safety device, test according to the
following instructions per electrical
configuration.
Cord-Connected 115 volt, 20 amp
models: The GFCI is located at the end
of the power cord. Before each use, with
the unit operating, push the TEST but-
ton. The unit should stop operating and
the GFCI power indicator will go out.
Wait 30 seconds and then reset the GFCI
by pushing the RESET button. The GFCI
power indicator will turn on, restoring
power to the hot tub. If the interrupter
does not perform in this manner, there
may be an electrical malfunction and
with it, the possibility of an electric
shock. Disconnect the power until the
problem has been corrected.
• 2x120 volt, permanently connected or
converted models:
• A ground terminal is provided on the
terminal block (TB-1, system ground ter-
minal) located inside the control box. To
reduce the risk of electric shock, connect
this terminal to the grounding terminal
of your electrical service or supply panel
with a continuous green, insulated cop-
per wire. The wire must be equivalent in
size to the circuit conductors supplying
the equipment. In addition, a bonding
terminal (pressure wire connector) is
provided on the outside of the control
box for bonding to local ground points.
To reduce the risk of electric shock, this
connector should be bonded with a No.
8 AWG (8.4 mm²) solid copper wire to
any metal ladders, water pipes, or other
metal within 5 feet (1.5 m) of the hot tub
to comply with local requirements. The
means of disconnection must be readily
accessible, but must be installed at least
5 feet (1.5 m) from the hot tub.
• Your hot tub is provided with a suitably
rated circuit breaker to open all un-
grounded supply conductors.
• Your hot tub uses ground fault circuit
interrupters in the electrical subpanel.
Before each use of the hot tub and with
the unit operating, push the TEST button
on each breaker. The switch should
click over to the “Trip” position. Wait
30 seconds and reset each GFCI breaker
by switching it completely off and then
completely on.
The switch should then stay on. If either
of the interrupters does not perform in this
manner, it is an indication of an electrical
malfunction and the possibility of an elec-
tric shock. Disconnect the power until the
fault has been identified and corrected.
SAFETY INSTRUCTIONS
7
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bueno Spa Chicago at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bueno Spa Chicago in the language / languages: English as an attachment in your email.

The manual is 6.43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info