636468
40
Zoom out
Zoom in
Previous page
1/68
Next page
6720818454 (2016/02) US SSB
40 | Troubleshooting
Verify that the value of CO2 is stable and is within the range indicated in
the following table (be careful to make small changes and conrm that the
value is stable before making additional adjustment).
Select “Low Power” using “UP/Down” button and press “OK”:
The fan will run at the minimum speed.
To adjust the CO2 value at the minimum power turn the screw “B” shown
in Fig. 68 and in Fig. 70.
Verify that the value of CO2 is stable and is within the range indicated in
the following table (be careful to make small changes and conrm that the
value is stable before making additional adjustment).
Select “OFF” using “UP/Down” button and press “OK”:
The “Test State” switches to OFF and the boiler return to the “stand by”
mode.
Gas Type Max. power CO2% Min. power CO2%
Natural gas 8.8-9.2 8.8-9.2
LP gas 10.3-10.7 10.3-10.7
Tab. 16 CO2 value for gas valve calibration
Tab. 17 indicates the approximate number of turns required to start the
boiler when when LPG conversion kit has been installed. [refer to section
4.6.2 for NG to LPG conversion instructions].
The number of turns has been counted from when the maximum and
minimum adjustment has been wound fully closed.
This procedure is not applicable to the minimum setting of SSB399 and
SSB512 valve [see Tab. 17].
These are approximate gures for LPG gas appliances. A combustion
analyzer must be used to set maximum and minimum CO2 as listed in
table Tab. 16.
Appliance
Maximum setting Minimum setting
Number of turns from gas
valve fully wound home
Number of turns from gas
valve fully wound home
SSB255 10 turns 2 and ¼ turns
SSB399 7 turns NA
SSB512 7 turns NA
Tab. 17 Number of turns for gas valve settings
5.8 Setting frost protection
The boiler is equipped with a system frost protection function, see section
“5.5 Parameters list” for a list of all parameters and settings.
The factory default setting Frost Protection (parameter # 89) is
“DISABLED”. To enable frost protection simply adjust parameter # 89 to
“ENABLE”. When the frost protection is enabled, Parameter #90 (Frost
Protection Setpoint) has to be set. Parameter #90 has a default setting of
50°F and can be adjusted from 33-68 °F.
When the supply temperature falls below the value set by the parameter
#90, the boiler pump starts.
If the supply temperature continues to fall and reaches 9 °F (5 °C) below the
value set by the parameter #90 the burner will switch on at minimum power.
When the supply temperature increases to a temperature of 9 °F (5°C)
greater than the value of the parameter # 90 the burner will switch off.
Then after the post circulation time has elapsed the pump will stop
(parameter #5 adjustable from 300-900 seconds. Default is 300 seconds).
For example, parameter #90 is set at 50 °F (10 °C), when the Supply
temperature is lower than 50 °F (10 °C) the pump starts. If the supply
temperature is lower than 41 °F (5 °C) the burner starts at the minimum power.
The burner switches off when a temperature of 59 °F (15 °C) is achieved.
NOTICE: This sequence protects the boiler only from
freezing. Be sure adequate measures are in place to protect
the system.
6 Troubleshooting
WARNING: Close the gas cock prior to working on the gas
train or “boiler”.
WARNING: Check for gas leaks after carrying out work on
the gas train.
WARNING: Check for leaks after carrying out work on the
venting system.
DANGER: Always disconnect the appliance from the
main power before performing any work. Disconnect the
emergency shutoff switch or disengage the heating system
circuit breaker. Take measures to prevent accidental
reconnection.
WARNING: Hot water can scald. Drain the appliance before
working on components that are lled with water.
6.1 Error codes are shown on the display
If the symbol appears on the screen as follow:
Fig. 71
an error has occurred in the system that is displayed on the screen. The
bottom row in the display will show the description of the error occurred.
System Test
Test State Low Power
Fan Speed 0 rpm
Ionisation 0.0 μA
System Test
Test State Off
Fan Speed 0 rpm
Ionisation 0.0 μA
04:29 pm
70.0°F
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Buderus SSB399 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Buderus SSB399 in the language / languages: English as an attachment in your email.

The manual is 9,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Buderus SSB399

Buderus SSB399 Installation Guide - French - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info