697320
75
Zoom out
Zoom in
Previous page
1/88
Next page
产品说明 | 75
6 720 816 739 (2015/05)MC 400
交付给运营商
交付产品时,应指导运营商如何操作供暖设备并告知运行条
件等信息。
解释操作过程,尤其是与安全有关的所有操作。
强调改装和维修只能由经过授权的专业人员执行。
强调检修和维护是确保安全和环保运行的前提。
将安装和操作说明书交给运营商保管。
冻结导致设备损坏
如果设备未运行,则可能结冰。
请注意防冻提示。
由于热水制备、锁闭保护等附加功能,请使设备始终保持
接通。
发生故障后立即排除。
2 产品说明
该模块用于控制级联系统。级联系统是一种使用多个热源的
采暖系统,其中使用多个热源,以获得更大的采暖输出功率。
参见例如 86 页的接线图。
该模块用于控制热源。
该模块用于记录室外温度、出水温度和回水温度。
用带有总线接口 EMS 2/EMS plus 的系统控制器配置级联系统
(不能使用所有的控制器)
模块组合方式参见连接图。
2.1 重要使用说明
模块通过一个 EMS 2/EMS plus 接口与其他 EMS 2/EMS plus 总线
用户进行通信。
模块可连接在具备总线接口 EMS 2/EMS plus (能源管理系
统)的控制器上。或者可通过模块上 0-10 V 接口连接外部
功率要求或温度要求。
模块仅与具备 EMSEMS 2EMS Plus 2 线总线 (HTIII) 的热
源通信GB112GB132 GB135 GB142 GB152 系列热
源除外)
仅将制造商的热源接入设备中。
在设备中使用以燃气为能源的热源或以燃油为能源的热源
(不允许使用带有总线接口 EMS 2/EMS plus 的热泵)
安装空间必须与模块技术参数规定的防护等级匹配。
当热水水箱直接连接到一个热源上时:
系统控制器或 0-10 V 控制器未显示任何热水系统信息且
对热水制备无任何影响。
推荐在直接热水制备时使用一个小于 400 升的蓄水器。
热水以及高温消毒都为热源直接控制。
高温消毒必须在必要时手动进行监测。注意热源说明
书。
无法在设备上对高温消毒进行监测时,不能将热水水箱
直接连接在热源上。
2.2 功能描述 / 控制策略
2.2.1 串联式标准级联
连接的热源 / 模块要接入或切断相应的布线。
例如,将接线端子 BUS1 上的热源第一个接入,接线端子
BUS2 上的热源等第二个接入。
关闭热源时,顺序相反。最后开启的热源,要作为第一个重
新关闭。
在此调节要考虑,热源在开启或关闭时的功率会突然上升或
下降。
2.2.2 串联式优化级联
所有目的是让热源以尽可能相同的燃烧器运行时间运行。
连接的热源要根据相应的燃烧器运行时间来开启或关闭。燃
烧器运行时间要每 24 小时进行一次比较并据此重新确定顺
序。
带有最短燃烧器运行时间的热源作第一个开启,带有最长燃
烧器运行时间的热源最后一个开启。
关闭热源时,顺序相反。最后开启的热源,要作为第一个重
新关闭。
在此调节要考虑,热源在开启或关闭时的功率会突然上升或
下降。
2.2.3 承担峰值负荷的串联式级联
热负荷在较长时间内平均分布 (基本负荷)并瞬时升高
(峰值负荷)时,该控制方案有意义。
接线端子 BUS1 BUS2 上的热源承担基本负荷。接线端子
BUS3 BUS4 上的热源开启,以满足峰值负荷时的能源需求。
当要求的出水温度超过设置的极限值或室外温度低于设置的
极限值时,接线端子 BUS3 BUS4 上的热源开启。
关闭热源时,顺序相反。最后开启的热源,要作为第一个重
新关闭。
在此调节要考虑,热源在开启或关闭时的功率会突然上升或
下降。
2.2.4 并联式级联
当热源调节比例相似时,使用该方案。
热源以尽可能相同的燃烧器运行时间运行。这时通常所有的
热源都要运行。当所有的热源以最低功率运行时,所有热源
调节的程度也要相同。
2.2.5 功率控制
当使用 0-10 V 输出的楼宇控制系统控制热源时,使用该控制
方案。
1 0-10 V
信号
U
单位为伏特)和要求功率
P
(设备最
大功率的百分比)之间的线性关系
连接的热源根据串联式标准级联或串联式优化级联时模块编
码所要求的功率开启并关闭。
如果热源配备的泵转速可以调控,一旦燃烧器
启动时转速过低,会出现高温和燃烧器节拍频
繁的情况。
如有可能,将泵的开 / 关运行功率设置为
100 %,此外尽量提高最低泵功率的设置值。
6 720 809 449-21.1O
P / %
U / V
1
10
100
1,5 10
75


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Buderus MC 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Buderus MC 400 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info