560473
88
Zoom out
Zoom in
Previous page
1/100
Next page
88
We reserve the right to make any changes due to technical modifications!
Installation and Servicing Instructions Logamax plus GB142-24/30/45/60 • Version 12/2004
Buderus Hydronic Systems • http://www.buderus.net
Appendix16
16.2 Error messages
z Press the "Service" button to display the service
code (e. g. "$").
z Press the "Service"
button to display the error
code (e. g. "").
The error message is a combination of the service code
(e. g. "$") and the error code (e. g. ""). You can only
resolve the error message using the Service chapter in
this manual.
INSTRUCTION FOR INSTALLERS
The display may also show system faults
(e. g. "$"). In principle, they are identified by
the initial letter "A" and they refer to faults
between the appliance and the additionally
available electronic components.
Display Meaning
Flame monitoring
$  No ionization message after ignition.
& 

Ionization measured before burner start.
/The flame went out during the heating phase.
3Hot-surface ignitor on for too long.
Grid voltage
&The grid power was interrupted after an error.
/

UBA fault.
External switching contact
< External switching contact, e. g. temperature
safety switch for floor heating, has taken place.
System faults
$Communication fault between UBA and KIM.
+


UBA fault.
3UBA fault.
/


Faulty gas burner fitting cable connection.
8KIM out of order.
< Communication fault between BC10 basic
controller and UBA.
( System faults
$&
)+/
<
Internal UBA fault.
Display Meaning
Water flow / water pressure
(System pressure too low < 3 psi (20 mbar).
)Temperature difference between safety and
supply sensors too much or no temperature
increase after starting the burner.
/Test of pump operation via a pressure increase
in the heating system (during pump start).
3 Temperature increase of safety sensor or supply
sensor too high.
8 Temperature difference between supply and
return sensor too much.
< Pump feedback fault.
Fan speed
$Fan unit failed during operation.
)Air volume flow not lost for 24 hours.
/Fan shut down during security test.
3Fan unit is running too slowly.
<Fan unit is running too fast.
Temperatures
$Supply sensor over 220 °F (105 °C).
(Sensor test failed
/  Safety sensor affected by short circuit or higher
than 266 °F (130 °C).
3  Loose contact or defective safety sensor.
8  Supply sensor affected by short circuit.
<  Loose contact or faulty supply sensor.
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Buderus Logamax plus GB142-30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Buderus Logamax plus GB142-30 in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Buderus Logamax plus GB142-30

Buderus Logamax plus GB142-30 User Manual - German - 16 pages

Buderus Logamax plus GB142-30 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info