697444

Buderus Logamatic 4322 Manual

9
Zoom out
Zoom in
Previous page
1/84
Next page
What you should know about your heating system
2
Logamatic 4321/4322 - Subject to technical modifications.
9
Why do I need a time switch?
Advanced heating systems are equipped with a time
switch to save energy. With a time switch you can set up
an automatic changeover between two different room
temperatures, subject to time. This enables you to set
a reduced room temperature at night, or other times
when a reduced temperature is sufficient, whilst
operating your heating system with the standard room
temperature during the day.
You have four options for reducing the room temperature
via the control unit. Upon request, your heating contractor
will select and set up one of these options:
– Total shutdown (no room temperature regulation)
– Reduced room temperature (a reduced room
temperature will be regulated)
– Change between total shutdown and reduced
heating subject to room temperature
– Change between total shutdown and reduced
heating subject to outside temperature
With total shutdown of the heating system, no pumps
or other system components are controlled. Heating
only recommences if the heating system is subject to
a risk of frost.
Heating with reduced room temperature (night mode)
only differs from standard heating mode (day mode)
through a lower flow temperature.
When changing from total shutdown to reduced
heating, total shutdown is activated subject to room
temperature when the actual room temperature
exceeds the set room temperature. This function is only
possible if a room temperature is being monitored.
When changing from total shutdown to reduced
heating, total shutdown is activated subject to outside
temperature when the actual outside temperature
exceeds the set outside temperature.
What are heating circuits?
A heating circuit describes the circuit taken by the
heating water from the boiler via the radiators and back
again (Æ Fig. 1, page 6). A simple heating circuit
comprises a heat source, a flow line, a radiator and
a return line. A pump installed in the flow line circulates
the heating water.
Several heating circuits may be connected to one
boiler, for example, one heating circuit for supplying
radiators and a further circuit for supplying an
underfloor heating system. In this case, the radiators
are supplied at a higher flow temperature than the
underfloor heating system.
The supply of different flow temperatures to different
heating circuits can be achieved by e.g. installing
a three-way valve between the boiler and the
underfloor heating circuit.
Using an additional temperature sensor in the flow of
the heating circuit to be supplied, sufficient cold return
water is mixed via a three-way valve into the hot flow
water, to achieve the required lower temperature. It is
important to note that heating circuits with three-way
valves require an additional pump. This pump enables
the second heating circuit to be operated independently
of the first heating circuit.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Buderus Logamatic 4322 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Buderus Logamatic 4322 in the language / languages: English as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info