631403
9
Zoom out
Zoom in
Previous page
1/52
Next page
8
1
CAUTION
4
Hold the needle with your left hand, and
then use a disc-shaped screwdriver to turn
the needle clamp screw counterclockwise
to remove the needle.
1 Use a disc-shaped screwdriver
2 Needle clamp screw
Do not use excessive force when loosening
or tightening the needle clamp screw,
otherwise certain parts of the sewing
machine may be damaged.
5
With the flat side of the needle toward the
back of the machine, insert the needle
until it touches the needle stopper. Next,
tighten the needle clamp using a disc-
shaped screwdriver.
Install the twin needle in the same way.
CAUTION
Changing the presser foot
CAUTION
You will have to change the presser foot depending on
what you want to sew and how.
1
Turn off the machine.
Raise the presser foot lever.
2
Raise the needle by turning the
handwheel toward you
(counterclockwise) so that the mark on
the wheel points up.
3
Press the black button at the back of the
presser foot holder to release the presser
foot.
4
Put a different presser foot on the needle
plate so that the bar on the presser foot is
in line with the slot on the shank.
Before replacing the needle, place fabric
or paper under the presser foot to
prevent the needle from falling into the
hole in the needle plate.
1 Use a disc-shaped
screwdriver
2 Needle stopper
3 Needle
21
2
3
1
Make sure you insert the needle until it
touches the stopper, and securely tighten
the needle clamp screw with a disc-
shaped screwdriver, otherwise the
needle may break or the machine may be
damaged.
Always turn off the machine before you
change the presser foot. If you leave the
power on and step on the controller, the
machine will start and you may be
injured.
Always use the correct presser foot for
the stitch pattern you have chosen. If
you use the wrong presser foot, the
needle may strike the presser foot and
bend or break, and may cause injury.
Only use presser feet that have been
designed to be used with this machine.
Using any other presser foot may cause
accident or injury.
1 Black button
2 Presser foot holder
3 Presser foot
1
2
3
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XR27NT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XR27NT in the language / languages: English as an attachment in your email.

The manual is 18,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info