525945

Brother XR-46C Manual

73
Zoom out
Zoom in
Previous page
1/99
Next page
62
BUTTONHOLE AND BUTTON SEWING
COUTURE DE BOUTONNIERES ET DE BOUTONS
OJALES Y COSTURA DE BOTONES
Button Sewing
Pattern Stitch Length Stitch Width Foot
0 Less than 5
1. Measure the distance between the holes and set the appropriate
stitch width using the Stitch Width Dial. For example, if the
distance between the holes is 1.5 mm, set the stitch width to 1.5.
2. Change the foot to the Zigzag presser foot.
3. Remove the power supply plug from the outlet. And place the
darning plate on the needle plate. Connect the power supply
plug into a wall outlet.
4. Place a button between the foot and the fabric and make sure
that the needle enters the holes without hitting the button. If it hits
see Step 1.
5. At a slow speed, sew approximately 10 stitches.
6. Remove the material from the machine. Cut the upper and lower
threads and tie both threads at the back of the material.
CAUTION
Make sure the needle does not strike the button during
sewing. The needle may break, leading to injury.
Zigzag Presser
Foot
Costura de botones
Modelo de Largo de Ancho de
Prensatelas
puntada puntada puntada
0 Menos de 5
Prénsatelas
para zigzag
1. Mida la distancia entre los orificios y ajuste el ancho de puntada
correspondiente con el selector adecuado. Por ejemplo, si la
distancia es de 1,5 mm, ajuste el ancho de puntada en 1,5.
2. Cambie el prensatelas por uno para zigzag.
3. Desenchufe la clavija de alimentación de la toma de corriente, y
ponga la placa de zurcir en la placa de la aguja. Conecte el
enchufe de alimentación a una toma de corriente.
4. Coloque un botón entre el prensatelas y el tejido y asegúrese de
que la aguja pase por los agujeros sin picar el botón. Si golpea el
botón, véase el punto 1.
5. Cosa unas 10 puntadas a baja velocidad.
6. Retire el tejido de la máquina. Corte los hilos inferior y superior y
haga un nudo con ambos en el revés del tejido.
PRECAUCIÓN
Asegúrese de que la aguja no roza el botón mientras cose. La
aguja podría romperse y causar lesiones.
Pour coudre un bouton
Modèle de Longueur de Largeur de Pied-de
point point point -biche
0 Moins de 5 Pied pour zigzag
1. Mesurer la distance entre les trous du bouton et régler la largeur de
point appropriée à l’aide du sélecteur correspondant. Par exemple, si
la distance entre les trous est de 1,5 mm, régler la largeur de point sur
1,5.
2. Remplacer le pied habituel par un pied pour zigzac.
3. Débrancher le cordon dálimentation de la prise. Placer la plaque à
repriser sur la plaque d'aiguille. Brancher la fiche d’alimentation à une
prise secteur.
4. Placer un bouton entre le pied et le tissu et veiller à ce que l’aiguille
pique dans les trous sans heurter le bouton. Si jamais elle heurte le
bouton, veuillez vous reporter au point 1.
5. Coudre environ 10 points à faible vitesse.
6. Retirer le tissu de la machine. Couper les fils inférieur et supérieur puis
les nouer sur l’envers du tissu.
ATTENTION
Pendant la couture, veillez à ce que l´aiguille ne touche pas le
bouton. L´aiguille risque de casser et vous pourriez vous blesser.
… 73 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XR-46C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XR-46C in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info