535078

Brother XL5200 Manual

54
Zoom out
Zoom in
Previous page
1/88
Next page
45
BUILT-IN STITCHES
PUNTADAS INCORPORADAS
POINTS INCLUS
Overedge Stitching
XL5300 XL5200 XL5100
Pattern Stitch Length Stitch Width
PX300 PX200 PX100
14 12 15 Stretch Overlock Stitch 3-5
15 13 12 Elastic Overlock Stitch Fixed 2.5
Fixed 5
17 15 11 Arrow Head Stitch
These stitches are used to join together seams and finish them in one
step. The Elastic Overlock is useful when sewing stretch materials, while
the Arrow head Stitch is ideal for sewing the edge of a blanket.
1. Set the pattern selection dial to the Elastic Overlock, Stretch
Overlock or Arrow Head.
2. Position the fabric under the presser foot so that the seamline is
approximately 3 mm (1/8") to the left of the presser foot center. This
stitch works best with a seam allowance of approximately 6 mm
(1/4") as this allows the right side of the stitch to overlock the cut
edge of the fabric as shown in fig. A.
3. If the seam allowance is wider than the stitch pattern, trim away
any excess fabric after stitching.
A finished Elastic Overlock is shown in fig. B.
A
B
Puntada por encima de la orilla
XL5300 XL5200 XL5100
Número de puntada
Largo de puntada
Ancho de puntada
PX300 PX200 PX100
14 12 15
Puntada overlock
3-5
15 13 12
Puntada overlock elástica
Fija 2,5
Fija 5
17 15 11
Puntada
punta de flecha
Estas puntadas se usan para juntar costuras y acabarlas en una
sola operación. La puntada overlock elástica se utiliza en costuras
de tejidos elásticos, mientras que la puntada punta de flecha resulta
ideal para la costura de dobladillos de mantas.
1. Ponga el selector de puntadas en puntada overlock elástica,
pespunto overlock o puntada punta de flecha.
2. Coloque el tejido debajo del prensatelas para que la línea de
costura quede unos 3 mm (1/8") a la izquierda del centro del
prensatelas. Esta puntada da los mejores resultados con una to-
lerancia de costura de unos 6 mm (1/4") dado que así permite a
la parte derecha de la puntada enganchar la orilla cortada del
tejido tal y como se muestra en la fig. A.
3. Si la tolerancia de costura es más ancha que la puntada, corte
cualquier pedazo de tejido que sobre después de coser.
En la fig. B puede ver una puntada overlock elástica.
Points sur le bord
XL5300 XL5200 XL5100
Modèle
Longueur de point
Largeur de point
PX300 PX200 PX100
14 12 15 Point o
verlock
stretch 3-5
15 13 12 Point overlock élastique Fixe 2,5
Fixe 5
17 15 11 Point flèche
Ces points servent à assembler des coutures et à les terminer en une seule
opération. Le point overlock élastique sert pour la couture de tissus élasti-
ques alors que le point flèche convient parfaitement à la couture des bords
d’une couverture.
1. Mettre le sélecteur de modèle de point sur le point overlock élastique,
sur le point overlock stretch ou sur le point flèche.
2. Placer le tissu sous le pied-de-biche de sorte que la couture se trouve
environ à 3 mm à gauche du centre du pied-de-biche. Ce point donne
d’excellents résultats avec une marge de couture de 6 mm, ce qui per-
met au côté droit (côté zigzag) du point de piquer le bord coupé du tissu
comme le montre la fig. A.
3. Si l’écart est supérieur à la taille du point, couper l’excédent de tissu
après avoir piqué.
La fig. B montre un point overlock stretch (à droite) terminé.
… 54 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XL5200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL5200 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info