Manual Brother XL5200 (page 16 of 88) (English, French, Spanish)

535078

Zoom out

Zoom in

1/88

KNOWING YOUR SEWING MACHINE

CONOZCA SU MÁQUINA DE COSER

CONNAÎTRE SA MACHINE À COUDRE

Inserting the Needle

Turn power switch to “O”.

1. Remove the power supply plug from the electrical outlet.

2. Raise the needle bar to its highest position.

3. Lower the presser foot.

4. If a needle is already installed, remove it by loosening the needle

clamp with a coin and pulling the needle down. (See fig. A.)

5. With the flat side toward the back, insert the new needle as far as

possible up against the needle stopper.

6. Tighten the needle clamp.

1 Coin

Checking the Needle

1. The sewing needle must always be straight and sharp for smooth

sewing.

2. To check if the needle is bent, place the flat side of the needle

down as shown in the illustration. (See fig. B.)

3. Replace the needle if it is bent or dull.

1 1

Inserción de la aguja

Desenchufar la máquina, interruptor principale a “O”.

1. Retire el enchufe de alimentación de la toma de corriente.

2. Levante la barra de la aguja a su posición más alta.

3. Baje el prensatelas.

4. En caso de que ya esté una aguja instalada, retírela aflojando el

tornillo con una moneda y tirando hacia abajo. (Ver fig. A.)

5. Introduzca una nueva aguja con la parte plana hacia atrás, lo

más adentro posible hasta que llegue a su tope.

6. Vuelva a apretar el tornillo de la aguja.

1 Moneda

Comprobación de la aguja

1. La aguja siempre ha de estar bien recta y afilada para un perfec-

to cosido.

2. Para comprobar que la aguja no está doblada, coloque la parte

plana de la aguja hacia abajo como se muestra en el dibujo. (Ver

fig. B.)

3. Cambie la aguja si está doblada o gastada.

Pour mettre l’aiguille en place

Mettre l’interrupteur principal sur “O”.

1. Retirer la fiche de la prise de courant.

2. Remonter complètement l’aiguille.

3. Abaisser le pied-de-biche.

4. Retirer l’aiguille éventuellement présente en dévissant la fixation avec

une pièce de monnaie et en tirant l’aiguille vers le bas. (Voir fig. A.)

5. Introduire une autre aiguille côté plat vers l’arrière, en l’enfonçant au

maximum jusqu’à ce qu’elle vienne heurter le butoir.

6. Resserrer la fixation.

1 Pièce de monnaie

Vérification de l’aiguille

1. L’aiguille doit toujours être droite et pointue pour piquer correctement.

2. Pour vérifier si l’aiguille n’est pas tordue, placer le côté plat de l’aiguille

vers le bas, comme le montre l’illustration. (Voir fig. B.)

3. Remplacer l’aiguille si elle est tordue ou usée.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL5200 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brother XL5200 Manual

Product: