631402
25
Zoom out
Zoom in
Previous page
1/111
Next page
13
Changing the Presser Foot
CAUTION
Always turn off the power before changing the presser
foot. If the power is on and the Start/Stop button is
pressed or foot controller is stepped on, the machine
will start and may cause injury.
Always use the correct presser foot for the selected
stitch pattern. If the wrong presser foot is used, the
needle may strike the presser foot and bend or break,
and may cause injury.
Only use presser feet for this machine. Using other
presser feet may lead to accident or injury.
It may be necessary to change the presser foot according to your
sewing needs.
SNAP-ON TYPE
1. Raise the needle to its highest position by turning the balance
wheel toward you (counter clockwise) and raise the presser foot
lever.
2. Release the foot by raising the lever located at the back of the
holder.
3. Place a different presser foot on the needle plate so that the bar
on the presser foot is in line with the slot on the shank.
4. Lower the presser foot lever and fix the presser foot onto the
shank. If the presser foot is in the correct location, the bar should
snap in.
Cambio del prensatelas
PRECAUCIÓN
Desenchufe siempre la máquina de la alimentación antes de
cambiar el pie prensatela. Si la máquina de coser está enchu-
fada a la corriente y pulsa el botón Marcha/Parada o si pisa el
pedal, la máquina se pondrá en funcionamiento y podría
hacerse daño.
Utilice siempre el pie prensatela adecuado para el pespunte
seleccionado. Si utiliza un pie prensatela inadecuado, la aguja
podría chocar contra el pie prensatela y doblarse o romperse,
lo que puede causar lesiones.
Use el pie prensatela sólo para esta máquina de coser. Si usa
otro pie prensatela, podría causar una avería o hacerse daño.
Según sus necesidades de costura, puede ser necesario cambiar el
prensatelas.
TIPO DE ENGANCHE DE GOLPE
1. Levante la aguja a su posición más alta, girando la ruedecilla hacia
usted (en el sentido contrario al de las manecillas de un reloj) y levante
la palanca del prensatelas.
2. Suelte el prensatelas levantando la palanca que hay en la parte trasera
del soporte.
3. Coloque otro prensatelas en la placa de agujas de tal forma que la barra
del prensatelas quede alineada con la ranura del soporte.
4. Baje la palanca del prensatelas y fije el prensatelas en el soporte. Si el
prensatelas está bien colocado, la barra debe engancharse de golpe.
Sostituzione del piedino premistoffa
ATTENZIONE
Prima di sostituire il piedino premistoffa, spegnere sempre la
macchina. Se la macchina è accesa e si preme inavvertitamente
il pulsante Avvio/Stop o il reostato a pedale la macchina
inizierà a operare con rischi di lesioni personali.
Utilizzare sempre il piedino premistoffa appropriato per il
motivo di punto selezionato. Se si utilizza un piedino
premistoffa errato, l’ago potrebbe colpire il piedino e piegarsi
o rompersi, con rischi di lesioni personali.
Utilizzare esclusivamente piedini premistoffa studiati per
questa macchina. L’uso di altri tipi di piedino può provocare
danni o lesioni personali.
In base alle esigenze del lavoro da eseguire, può rendersi necessario
sostituire il piedino premistoffa.
PIEDINO DI TIPO A SCATTO
1. Far salire l’ago fino alla sua posizione più alta girando il volantino
verso se stessi (in senso antiorario) e sollevare la leva del piedino
premistoffa.
2. Staccare il piedino sollevando la levetta situata dietro il gambo.
3. Posizionare il nuovo piedino sulla placca dell’ago in modo che il
perno del piedino sia allineato rispetto alla scanalatura del
gambo.
4. Abbassare la leva del piedino in modo che il piedino si innesti nel
gambo. Se il piedino è nella posizione corretta, il perno scatterà
in posizione.
TABLE OF CONTENTS
KNOWING YOUR
SEWING MACHINE
STRAIGHT AND
ZIGZAG STITCHING
BUILT-IN STITCHES
BUTTONHOLE AND
BUTTON SEWING
USING ATTACHMENTS
AND APPLICATIONS
MAINTENANCE
INDEX
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XL-6600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL-6600 in the language / languages: English, Italian, Spanish as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother XL-6600

Brother XL-6600 User Manual - German, Dutch, French - 109 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info