631398
78
Zoom out
Zoom in
Previous page
1/101
Next page
67
USING ATTACHMENTS AND APPLICATIONS
HEFTEN UND APPLIZIEREN
ИСПОЛЬЗОВАНИЕ ПРИСПОСОБЛЕНИЙ И ИЗГОТОВЛЕНИЕ АППЛИКАЦИЙ
Нажимная
лапка зигзаг
Darning
Pattern Stitch Length Foot
(Straight Stitch
Any
(Left Needle Position))
(Straight Stitch
(Center Needle Position))
1. Remove the power supply plug from the outlet. And place the
darning plate on the needle plate as shown in fig. A. Connect the
power supply plug into a wall outlet.
2. Set the Pattern Selection Dial to Straight Stitch.
3. Place the portion to be darned under the presser foot together
with a fabric for reinforcement.
4. Lower the presser foot.
5. Begin sewing alternating between gently drawing the work away
from you and pulling it toward you.
6. Repeat this motion until the portion to be darned is filled with
parallel lines of stitching.(See fig. B)
Stopfen
Stichmuster Stichlänge Stichbreite
(Geradstich
Beliebig
(Nadelposition links))
(Geradstich
(Nadelposition Mitte))
1. Schalten Sie die Maschine am Hauptschalter aus. Setzen Sie die
Stopfplatte auf die Nadelplatte, wie in Abb. A gezeigt. Schalten Sie die
Maschine am Hauptschalter wieder ein.
2. Stellen Sie das Stichmuster-Einstellrad auf den Geradstich ein.
3. Legen Sie die zu stopfende Stelle zusammen mit einer Stoffunterlage
zur Verstärkung unter den Nähfuß.
4. Senken Sie den Nähfuß.
5. Beginnen Sie mit dem Nähen, während Sie den Stoff leicht vor und
zurück bewegen.
6. Wiederholen Sie diese Bewegung, bis die betreffende Stelle mit
parallelen Stichlinien ausgefüllt ist. (Siehe Abb. B)
B
A
Zigzag Presser
Foot
Zickzack-
Nähfuß
Штопка
Стежок Длина стежка
Нажимная лапка
ямой стежок
(
Левое положение иглы
))
Любая
ямой стежок
(Цент альное положение иглы))
1. Отсоедините штепсель шну а питания от озетки.
Разместите пластину для штопки на игольной пластине,
как показано на ис. А. Подсоедините штепсель шну а
питания к озетке.
2. Установите учку выбо а типа стежка на п ямой стежок.
3. Поместите участок изделия, подлежащий емонту, вместе
с подложенной под него заплаткой под нажимную лапку.
4. Опустите нажимную лапку.
5. Начните ст очку, попе еменно медленно пе емещая
п ошиваемую деталь в нап авлении от себя и на себя.
6. Повто яйте эти движения до тех по , пока вся
емонти уемая часть не пок оется па аллельными
стежками. (См. Рис. В)
78


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XL-6050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL-6050 in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother XL-6050

Brother XL-6050 User Manual - German, Dutch, French - 101 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info