579803

Brother XL-5340 Manual

67
Zoom out
Zoom in
Previous page
1/77
Next page
59
CONTENTS
KNOWING YOUR
SEWING MACHINE
STRAIGHT AND
ZIGZAG STITCHING
BUILT-IN STITCHES
BUTTONHOLE AND
BUTTON SEWING
USING ATTACHMENTS
AND APPLICATIONS
MAINTENANCE
INDEX
Cleaning
Removing the Shuttle Hook
1. Raise the needle to its highest position and remove the power sup-
ply plug from the outlet.
2. Remove the extension table and open the shuttle cover on the front
of the free arm.
3. Take out the bobbin case by opening its latch and pulling it out
from the shuttle race.
4. Slide the latch levers out from the retaining ring to remove it. (See
fig. A.)
5. Remove the hook by grasping its center post and pulling it out as
shown in fig. B.
NOTE:
When the needle is lowered, the shuttle hook cannot be removed.
Cleaning the Shuttle Race
1. Remove any accumulated lint and thread from the retaining ring,
hook, driver and race body with a brush.
2. A cloth dampened with machine oil should be used to wipe lint
from the shuttle race.
3. Clean the shuttle hook as described is step 2.
4. Reassemble and push the latch levers back to their previous posi-
tions holding the retaining ring in place with the notch at the top.
1 Retaining ring
2 Latch lever
3 Hook
4 Driver
5 Race body
Cleaning the Feed Dogs
1. Remove the needle plate using a coin to remove the screws.
2. Clean the upper part of the feed dogs and shuttle race body with a
brush.
A
1
2
5
1
4
3
1
B
C
Limpieza
Para sacar el gancho de la lanzadera
1. Levante la aguja a su posición más alta y apague la máquina.
2. Retire la tabla de extensión y abra la cubierta exterior de la lan-
zadera de la parte frontal del brazo libre.
3. Saque el portacanilla abriendo su uñeta metálica (pestillo) y reti-
rándolo de la pista de la lanzadera.
4. Retire las palancas que sujetan el anillo retenedor y saque dicho
anillo. (Ver fig. A.)
5. Retire el gancho cogiéndolo de la barra central y sacándolo tal y
como se muestra en la fig. B.
NOTA:
No puede quitarse el gancho cuando la aguja está bajada.
Limpieza de la pista de la lanzadera
1. Quite los hilos y polvo acumulados en el anillo retenedor, gan-
cho, impulsor y pista con un cepillo.
2. Limpie el polvo de la lanzadera con un trapo impregnado de acei-
te de máquina.
3. Limpie el gancho de la misma manera.
4. Vuelva a juntar los elementos y coloque las palancas en sus po-
siciones previas para que mantengan el anillo retenedor en su
sitio con la hendidura hacia arriba.
1 Anillo retenedor
2 Palanca de la uñeta
3 Gancho
4 Impulsor
5 Pista de la lanzadera
Limpieza de los alimentadores
1.
Retire la placa de agujas con una moneda para aflojar los tornillos.
2. Limpie la parte superior de los alimentadores y el cuerpo de la
lanzadera con un cepillo.
Nettoyage
Comment retirer le crochet de la navette
1. Remonter complètement l’aiguille et retirer la fiche de la prise de cou-
rant.
2. Retirer la table d’extension et ouvrir le couvercle de la navette, devant le
bras libre.
3. Sortir le boîtier de la canette en tirant sur la languette métallique pour le
sortir de la coursière.
4. Retirer les pattes de blocage de l’anneau de maintien et ôter l’anneau.
(Voir fig. A.)
5. Sortir le crochet en tirant sur son axe central, comme l’indique la fig. B.
REMARQUE:
Il est impossible de retirer le crochet de la navette lorsque l’aiguille est
abaissée.
Nettoyage de la coursière de la navette
1. A l’aide d’une petite brosse, enlever la bourre et le fil qui se sont accu-
mulés dans l’anneau de maintien, sur le crochet, dans l’entraînement et
sur la coursière.
2. Nettoyer la coursière avec un chiffon imbibé d’huile pour machine.
3. Nettoyer le crochet de la navette de la même manière.
4. Remonter le tout et remettre les pattes de blocage en place, tout en main-
tenant l’anneau de maintien avec l’encoche vers le haut.
1 Anneau de maintien
2 Patte de blocage
3 Crochet
4 Entraînement
5 Coursière
Nettoyage des griffes d’entraînement
1. Retirer la plaque à aiguille avec une pièce de monnaie pour desserrer les
vis.
2. Nettoyer la partie supérieure des griffes d’entraînement et de la cour-
sière de la navette à l’aide d’une brosse.
… 67 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XL-5340 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL-5340 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info