579803
39
Zoom out
Zoom in
Previous page
1/77
Next page
31
CONTENTS
KNOWING YOUR
SEWING MACHINE
STRAIGHT AND
ZIGZAG STITCHING
BUILT-IN STITCHES
BUTTONHOLE AND
BUTTON SEWING
USING ATTACHMENTS
AND APPLICATIONS
MAINTENANCE
INDEX
Straight Stitching
Pattern Stitch Length Stitch Width
(Straight Stitch) 1-4
5-0*
(Triple Stretch Stitch) Fixed 2.5
* Turn the stitch width dial to adjust the needle position. Setting the dial to “5”
selects the left needle position; setting the dial to “0” selects the right needle
position.
Starting Sewing
1. Turn the pattern selection dial to select the desired stitch. Set the
pattern selection dial to Straight Stitch or Triple Stretch Stitch for
the type of stitch required.
2. Raise the needle to its highest position and lift the presser foot lever.
3. Pull up the lower thread by turning the balance wheel toward you
(counterclockwise) and place both the upper and lower threads
behind the presser foot.
4. Place the fabric under the presser foot with the needle 1 cm (3/8")
from the edge of the fabric.
5. Lower the presser foot.
Backtacking
Reverse stitching is used to lock or reinforce the end of the stitch.
6. Press down on the reverse sewing lever as far as possible, then
lightly step on the foot controller. Sew 5 to 10 stitches in the re-
verse direction.
7. Release the reverse sewing lever and step down on the foot con-
troller to start sewing in the forward direction.
Puntadas rectas
Número de puntada
Largo de puntada Ancho puntada
(Puntada recta) 1-4
5-0*
(Puntada triple elástica) Fija 2,5
* Gire el selector de ancho de puntada para ajustar la posición de la aguja. Si
coloca el selector en la posición “5”, se selecciona la posición de la aguja a
la izquierda; si coloca el selector en “0”, se selecciona la posición de la aguja
a la derecha.
Para empezar a coser
1. Gire el selector de puntadas para seleccionar la puntada desea-
da. Ponga dicho selector de puntadas en puntada recta o punta-
da triple elástica para el tipo de puntada deseado.
2. Levante la aguja a su posición más alta y levante la palanca del
prensatelas.
3. Saque el hilo inferior girando la ruedecilla hacia usted (en el sen-
tido contrario a las manecillas de un reloj) y tire los hilos superior
e inferior hacia la parte trasera del prensatelas.
4. Coloque el tejido debajo del prensatelas con la aguja de 1 cm
(3/8") de la orilla del tejido.
5. Baje el prensatelas.
Retroceso
La puntada de retroceso se utiliza para finalizar una costura o refor-
zarla.
6. Baje la palanca de retroceso hasta el final y presione suavemen-
te el pedal. Cosa de 5 a 10 puntadas en la dirección de retroceso.
7. Suelte la palanca de retroceso y pise el pedal para volver a coser
hacia adelante.
Point droit
Modèle
Longueur de point
Largeur de point
(Point droit) 1-4
5-0*
(Triple point élastique) Fixe 2,5
* Tourner le sélecteur de largeur de point pour régler la position de
l’aiguille. Régler le sélecteur sur “5” pour placer l’aiguille à gauche et
sur “0” pour la placer à droite.
Pour commencer à coudre
1. Tourner le sélecteur de modèle jusqu’à la sélection du point souhaité. Régler le
sélecteur sur “point droit” ou “triple point élastique” en fonction du type de
point souhaité.
2. Remonter complètement l’aiguille et relever le levier du pied-de-biche.
3. Remonter le fil inférieur en tournant le volant vers soi (dans le sens opposé aux
aiguilles d’une montre) et tirer les deux fils, inférieur et supérieur, vers l’arrière
du pied-de-biche.
4. Placer le tissu sous le pied-de-biche et mettre l’aiguille à 1 cm du bord du tissu.
5. Abaisser le pied-de-biche.
Pour arrêter une couture en marche arrière
La piqûre en marche arrière sert à arrêter ou à consolider une couture.
6. Abaisser complètement le levier de couture en marche arrière et appuyer légè-
rement sur la pédale. Coudre 5 à 10 points en marche arrière.
7. Remonter le levier de couture en marche arrière et recommencer à coudre en
avant en appuyant sur la pédale.
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XL-5340 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL-5340 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info