579801

Brother XL-5130 Manual

63
Zoom out
Zoom in
Previous page
1/77
Next page
55
CONTENTS
KNOWING YOUR
SEWING MACHINE
STRAIGHT AND
ZIGZAG STITCHING
BUILT-IN STITCHES
BUTTONHOLE AND
BUTTON SEWING
USING ATTACHMENTS
AND APPLICATIONS
MAINTENANCE
INDEX
Monogramming and Embroidering
Pattern Stitch Length Stitch Width Foot
(Zigzag Stitch) Any Any None
Preparing for Monogramming and Embroidering
1. Place the darning plate on the needle plate.
(When the machine is equipped with a drop feed lever, lower the
feed dogs by setting the drop feed lever to the up position.)
2. Set the pattern selection dial to the appropriate Zigzag Stitch.
3. Draw the lettering (for monogramming) or design (for embroider-
ing) on the surface of the fabric.
4. Stretch the fabric between embroidery hoops as firmly as possible
with the reverse side of the fabric under the inside hoop.
5. Place the work under the needle and lower the presser bar with the
presser foot holder assembly removed.
6. Pull the lower thread up through the work at the starting position
by turning the balance wheel and make a few holding stitches.
7. Hold the hoop with the thumbs and forefingers of both hands while
pressing the fabric with the middle and third fingers and supporting
the outside of the hoop with your small fingers.
NOTE:
After sewing without feeding, prepare for the next seam by returning
the drop feed lever to the down position so that the feed dogs are
raised.
CAUTION:
Keep fingers away from moving parts, especially needles.
Monogramas y bordados
Número de puntada
Largo de puntada
Ancho de puntada
Prensatelas
(Puntada zigzag) Cualaquiera Cualaquiera
Quitarlo, sin
prensatelas
Preparación para monogramas y bordados
1. Coloque la placa de zurcido en la placa de la aguja.
(Cuando la máquina está equipada con una palanca de alimen-
tación de bajada, baje los ganchos de alimentación colocando la
palanca de alimentación de bajada en la posición hacia arriba).
2. Ponga el selector de puntadas en la puntada zigzag apropiada.
3. Dibuje las letras (para monogramas) o el diseño (para bordados)
en el derecho del tejido.
4. Estire el tejido en bastidor tanto como pueda y si es posible con
el revés abajo del circulo interior.
5. Coloque la tela debajo de la aguja y baje la barra del prensatelas
con su soporte.
6. Girando la ruedecilla, pase el hilo inferior por el trabajo y cosa
unas cuantas puntadas para asegurarlo.
7. Sujete el bastidor con el pulgar e índice de cada mano, presione
el tejido con los dedos medios y anulares y sostenga los exterio-
res del bastidor con los meñiques.
NOTA:
Después de haber cosido sin la alimentación, prepárese para la si-
guiente costura bajando la palanca para que se levanten los
alimentadores.
ATENCIÓN:
Mantenga los dedos alejados de las piezas móviles, especial-
mente de las agujas.
Monogrammes et broderies
Modèle
Longueur de point
Largeur de point
Pied-de-biche
(Point zigzag)
N’importe N’importe
Aucun
quelle longueur quelle longueur
Préparation avant de faire des monogrammes ou des broderies
1. Placer la plaque à repriser sur la plaque à aiguille.
(Lorsque la machine est équipée d’un levier d’abaissement des griffes
d’entraînement, abaisser les griffes en relevant le levier).
2. Mettre le sélecteur de modèle sur le point zigzag adéquat.
3. Dessiner les lettres (monogrammes) ou le motif (broderies) sur l’en-
droit du tissu.
4. Tendre au maximum l’ouvrage sur le tambour, en maintenant l’envers
du tissu dans le fond du cercle intérieur.
5. Placer l’ouvrage sous l’aiguille et abaisser la barre sans pied du pied-
de-biche.
6. Tirer le fil inférieur à travers l’ouvrage, au point de départ. Pour ce faire,
tourner le volant vers soi et piquer quelques points de maintien.
7. Saisir le tambour des deux mains, avec le pouce et l’index, tout en ap-
puyant sur le tissu avec le majeur et l’annulaire de chaque main. Les
auriculaires serviront à tenir l’extérieur du tambour.
REMARQUE:
Après la couture sans entraînement, préparer la machine pour la couture
suivante en rabaissant le levier des griffes d’entraînement afin de relever les
griffes.
PRÉCAUTION:
Veiller à tenir ses doigts à l’écart des éléments mobiles et notamment
des aiguilles.
… 63 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XL-5130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL-5130 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info