579801

Brother XL-5130 Manual

26
Zoom out
Zoom in
Previous page
1/77
Next page
18
CONTENTS
KNOWING YOUR
SEWING MACHINE
STRAIGHT AND
ZIGZAG STITCHING
BUILT-IN STITCHES
BUTTONHOLE AND
BUTTON SEWING
USING ATTACHMENTS
AND APPLICATIONS
MAINTENANCE
INDEX
THREADING THE MACHINE
Winding the Bobbin
1. Place the spool of thread on the spool pin and pass the thread
around the bobbin winding tension disc.
1 Bobbin winding tension disc
2 Bobbin winding
2. Pass the end of the thread through the hole in the bobbin from the
inside.
3. While turning the bobbin clockwise, slide it over the bobbin wind-
ing shaft so that the shaft spring slides into the slit in the bobbin.
Then, slide the shaft to the right.
3 Spring
4 Slit
4. While holding the end of the thread, gently press on the foot con-
troller to wind the thread around the bobbin a few times, then stop
the machine.
5. Trim the excess thread sticking out from the top of the bobbin and
continue winding the thread onto the bobbin by pressing down on
the foot controller.
NOTE:
The machine stops automatically when the bobbin is full.
6. When the machine stops, cut the thread, push the shaft to the left
and remove the full bobbin from the shaft.
CAUTION:
Although the needle bar does not move when the bobbin winding
shaft is slid toward the bobbin presser, the balance wheel will con-
tinue to turn. Therefore, do not touch the balance wheel while the
bobbin is being wound.
3
4
2
1
ENHEBRADO DE LA MÁQUINA
Bobinado de la canilla
1. Coloque un carrete de hilo en el portacarretes y pase el hilo por
el disco de tensión de bobinado de la canilla.
1 Disco de tensión de bobinado de la canilla
2 Bobinado de la canilla
2. Pase el extremo del hilo por el orificio de la canilla a partir del
interior.
3. Mientras gira la canilla en sentido de las manecillas de un reloj,
deslice el eje hacia el eje de bobinado de tal forma que el muelle
impulsor del eje se deslice dentro de la ranura de la canilla. Des-
lice el eje hacia la derecha.
3 Muelle
4 Ranura
4. Sujetando el extremo del hilo, presione suavemente el pedal para
que el hilo efectúe un par de vueltas alrededor de la canilla y
pare la máquina.
5. Deshaga el exceso de hilo arriba de la canilla. Siga bobinando el
hilo en la canilla presionando el pedal.
NOTA:
La máquina se para automáticamente cuando la canilla está llena.
6. Cuando la máquina se pare, corte el hilo, empuje el eje hacia la
izquierda y retire la canilla llena del eje.
ATENCIÓN:
Aunque la barra de la aguja no se desplace cuando el eje de
bobinado de la canilla se desliza hacia el apretador de la canilla,
la ruedecilla va a seguir girando y no puede ser tocada mien-
tras la canilla está bobinando.
ENFILAGE DE LA MACHINE
Remplissage de la canette
1. Placer la bobine de fil sur le porte-bobine et faire passer le fil par le
disque de tension du dévidoir.
1 Disque de tension du dévidoir
2 Remplissage de la canette
2. Passer l’extrémité du fil dans l’orifice de la canette, par l’intérieur.
3. Placer la canette sur le dévidoir et glisser celui-ci vers la droite. Tourner
la canette dans le sens des aiguilles d’une montre, à la main, jusqu’à ce
que le ressort de la broche se place dans la rainure de la canette.
3 Ressort
4 Rainure
4. Tout en tenant l’extrémité du fil, appuyer doucement sur la pédale pour
enrouler le fil autour de la canette. Arrêter la machine au bout de quel-
ques tours.
5. Couper le bout de fil dépassant au-dessus de la canette puis continuer à
enrouler le fil sur la canette en appuyant sur la pédale du rhéostat.
REMARQUE:
La machine s’arrête automatiquement lorsque la canette est pleine.
6. Lorsque la machine s’arrête, couper le fil, repousser le dévidoir vers la
gauche, et en retirer la canette pleine.
PRÉCAUTION:
Bien que la barre à aiguille ne fonctionne pas lorsque la broche du dé-
vidoir est glissée pour maintenir la canette, le volant à main va conti-
nuer à tourner. Dès lors, éviter de toucher le volant lors du remplissage
de la canette.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XL-5130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL-5130 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info