Manual Brother XL-5030 (page 72 of 82) (English, Italian, Spanish)

631388

Zoom out

Zoom in

1/82

CONTENTS

KNOWING YOUR

SEWING MACHINE

STRAIGHT AND

ZIGZAG STITCHING

BUILT-IN STITCHES

BUTTONHOLE AND

BUTTON SEWING

USING ATTACHMENTS

AND APPLICATIONS

MAINTENANCE

INDEX

Cleaning

Removing the Shuttle Hook

1. Raise the needle to its highest position and remove the power sup-

ply plug from the outlet.

2. Remove the extension table and open the shuttle cover on the front

of the free arm.

3. Take out the bobbin case by opening its latch and pulling it out

from the shuttle race.

4. Slide the latch levers out from the retaining ring to remove it. (See

fig. A.)

5. Remove the hook by grasping its center post and pulling it out as

shown in fig. B.

NOTE:

When the needle is lowered, the shuttle hook cannot be removed.

Cleaning the Shuttle Race

1. Remove any accumulated lint and thread from the retaining ring,

hook, driver and race body with a brush.

2. A cloth dampened with machine oil should be used to wipe lint

from the shuttle race.

3. Clean the shuttle hook as described is step 2.

4. Reassemble and push the latch levers back to their previous posi-

tions holding the retaining ring in place with the notch at the top.

1 Retaining ring

2 Latch lever

3 Hook

4 Driver

5 Race body

Cleaning the Feed Dogs

1. Remove the needle plate using a coin to remove the screws.

2. Clean the upper part of the feed dogs and shuttle race body with a

brush.

Limpieza

Para sacar el gancho de la lanzadera

1. Levante la aguja a su posición más alta y apague la máquina.

2. Retire la tabla de extensión y abra la cubierta exterior de la lan-

zadera de la parte frontal del brazo libre.

3. Saque el portacanilla abriendo su uñeta metálica (pestillo) y reti-

rándolo de la pista de la lanzadera.

4. Retire las palancas que sujetan el anillo retenedor y saque dicho

anillo. (Ver fig. A.)

5. Retire el gancho cogiéndolo de la barra central y sacándolo tal y

como se muestra en la fig. B.

NOTA:

No puede quitarse el gancho cuando la aguja está bajada.

Limpieza de la pista de la lanzadera

1. Quite los hilos y polvo acumulados en el anillo retenedor, gan-

cho, impulsor y pista con un cepillo.

2. Limpie el polvo de la lanzadera con un trapo impregnado de acei-

te de máquina.

3. Limpie el gancho de la misma manera.

4. Vuelva a juntar los elementos y coloque las palancas en sus po-

siciones previas para que mantengan el anillo retenedor en su

sitio con la hendidura hacia arriba.

1 Anillo retenedor

2 Palanca de la uñeta

3 Gancho

4 Impulsor

5 Pista de la lanzadera

Limpieza de los alimentadores

Retire la placa de agujas con una moneda para aflojar los tornillos.

2. Limpie la parte superior de los alimentadores y el cuerpo de la

lanzadera con un cepillo.

Pulizia

Rimozione della capsula dal crochet

1. Far salire l’ago fino alla posizione più alta e disinserire la spina di ali-

mentazione dalla presa elettrica.

2. Aprire lo sportello del crochet situato davanti al braccio libero.

3. Per togliere la capsula della spoletta, sbloccare il catenacciolo ed estrar-

re la capsula dal suo alloggiamento.

4. Per estrarre l’anello ferma-crochet, spingere in fuori le levette ferma-

anello. (Vedi fig. A.)

5. Estrarre il crochet prendendolo dal perno centrale e tirandolo come

mostrato in fig. B.

NOTA:

Il crochet non può essere estratto se l’ago è abbassato.

Pulizia della capsula

1. Togliere con uno spazzolino rimasugli di filo e polvere dall’anello fer-

ma-crochet, dal crochet, dalla guida e dalla capsula.

2. Pulire con un panno morbido imbevuto di olio per macchina da cucire

l’interno dell’alloggiamento del crochet.

3. Pulire il crochet nello stesso modo indicato al punto 2.

4. Rimontare e spingere le levette ferma-anello nella posizione precedente

tenendo in posizione l’anello ferma-crochet con l’intaglio rivolto verso

l’alto.

1 Anello ferma-crochet

2 Levetta ferma-anello

3 Crochet

4 Guida

5 Corpo dell’alloggiamento

Pulizia delle griffe di trasporto

1. Rimuovere la placca dell’ago svitando le viti con una moneta.

2. Pulire con uno spazzolino i dentini del trasportatore e il corpo

dell’alloggiamento del crochet.

I'm a complete notice, and need your help.
I was using my sewing machine and the unit that holds the needle came off the main rod that moves up and down.. There seems to be a tiny alan screw, is that what holds it on the rod? Would need a tiny alan key..

Thank you for any help..
Kind regards
Helen Submitted on 10-10-2020 at 20:19
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL-5030 in the language / languages: English, Italian, Spanish as an attachment in your email.

The manual is 1,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother XL-5030

Brother XL-5030 User Manual - German, Dutch, French - 85 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brother XL-5030 Manual

Product: