631380

Brother X-5 Manual

20
Zoom out
Zoom in
Previous page
1/67
Next page
12
Reverse Sewing Lever
To sew in reverse, press down the reverse sewing lever as far as
possible and hold it in that position while lightly stepping on the
foot controller. To sew forward, release the reverse sewing lever.
Reverse sewing is used for locking and reinforcing seams.
THREADING THE MACHINE
Winding the Bobbin
1. Place the spool of thread on the spool pin and pass the thread
around the bobbin winding tension disc.
a Bobbin winding tension disc
b Bobbin winding
2. Pass the end of the thread through the hole in the bobbin from
the inside.
2. Place the bobbin onto the bobbin winding shaft and slide the
shaft to the right. Turn the bobbin clockwise, by hand, until
the spring on the shaft slides into the slit on the bobbin.
c Spring
d Slit
4. While holding the end of the thread, gently press on the foot
controller to wind the thread around the bobbin a few times,
then stop the machine.
3. Trim the excess thread sticking out from the top of the bobbin
and continue winding the thread onto the bobbin by pressing
down on the foot controller.
NOTE:
The machine stops automatically when the bobbin is full.
6. When the machine stops, cut the thread between bobbin and
spool, push the shaft to the left and remove the full bobbin
from the shaft.
CAUTION:
Although the needle bar does not move when the bobbin
winding shaft is slid toward the bobbin presser, the balance
wheel will continue to turn. Therefore, do not touch the balance
wheel while the bobbin is being wound.
Levier de couture en marche arrière
Pour coudre en arrière, abaisser au maximum le levier de couture
en marche arrière, et le maintenir dans cette position tout en
appuyant légèrement sur la pédale. Pour coudre à nouveau vers
l’avant, relâcher le levier. Utiliser la couture en marche arrière
pour arrêter ou renforcer une couture.
ENFILAGE DE LA MACHINE
Remplissage de la canette
1. Placer la bobine de fil sur le porte-bobine et faire passer le fil
par le disque de tension du dévidoir.
a Disque de tension du dévidoir
b Remplissage de la canette
2. Passer l’extrémité du fil dans l’orifice de la canette, par
l’intérieur.
3. Placer la canette sur le dévidoir et glisser celui-ci vers le
droite. Tourner la canette dans le sens des aiguilles d’une
montre, à la main, jusqu’à ce que le ressort de la broche se
place dans la rainure de la canette.
c Ressort
d Rainure
4. Tout en tenant l’extrémité du fil, appuyer doucement sur la
pédale pour enrouler le fil autour de la canette. Arrêter la
machine au bout de quelques tours.
5. Couper le bout de fil dépassant au-dessus de la canette puis
continuer à enrouler le fil sur la canette en appuyant sur la
pédale du rhéostat.
REMARQUE:
La machine s’arr
ê
te automatiquement lorsque la canette est pleine.
6. Lorsque la machine s’arrête, couper le fil entre la canette et la
bobine, pousser le dévidoir vers la gauche et en retirer la
canette pleine.
PRECAUTION:
Bien que la barre à aiguille ne fonctionne pas lorsque la broche
du dévidoir est glissée pour maintenir la canette, le volant à main
va continuer à tourner. Dès lors, éviter de toucher le volant lors
du remplissage de la canette.
Palanca de retroceso
Para coser hacia atrás, baje completamente la palanca de retroceso y
manténgala en esa posición mientras presiona ligeramente el pedal.
Para volver a coser hacia adelante, vuelva a subir la palanca de
retroceso. La costura hacia atrás se usa para terminar y reforzar
costuras.
Alavanca de retrocesso
Para inverter o sentido da costura, pressione ao máximo a alavanca de
retrocesso e retenha-a nessa posição, acionando simultânea e
levemente o pedal do motor. Para voltar a costurar para frente, solte a
alavanca. A costura em sentido inverso utiliza-se para rematar e
reforçar costuras.
… 20 …


Need help? Post your question in this forum.

Forumrules
1

Forum

brother-x-5

Reset search

  • my Brother X5 is looping at the back of the material Submitted on 31-5-2023 at 14:57

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother X-5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother X-5 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother X-5

Brother X-5 User Manual - German, Dutch, French, Italian - 66 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info