606047
55
Zoom out
Zoom in
Previous page
1/93
Next page
48
BUILT-IN STITCHES
PUNTADAS INCORPORADAS
Puntada por encima de la
orilla
Modelo de puntada
Largo de puntada
Ancho de puntada
(Puntada peine)
(Puntada overlock estrecha)
3-5
(Puntada overlock elástica)
(Puntada ondas elástica)
F-3
Estas puntadas se usan para juntar costuras y
acabarlas en una sola operación. La puntada overlock
elástica es ideal para coser tejidos elásticos.
1. Sitúe el selector de puntada en puntada peine,
puntada overlock elástica o puntada ondas
elástica.
2. Coloque el tejido debajo del prensatelas para que
la línea de costura (con la puntada de flecha)
quede unos 3 mm (1/8") a la izquierda del centro
del prensatelas. Esta puntada da los mejores
resultados con una tolerancia de costura de unos
6 mm (1/4") dado que así permite a la parte
derecha (zigzag) de la puntada enganchar la
orilla cortada del tejido tal como ilustrado en la fig.
A.
3. Si la tolerancia de costura es más ancha que la
puntada, corte cualquier pedazo de tejido que
sobre después de coser.
En la fig. B, puede ver una puntada overlock elástica
acabada.
Cuando cosa la puntada overlock estrecha, ponga el
tejido de forma que su borde quede a la izquierda de
la aguja. (Ver la fig. C)
Overedge Stitching
Pattern Stitch Length Stitch Width
(Comb Stitch)
(Slant Overlock Stitch)
3-6
(Elastic Overlock Stitch)
(Elastic Shell Tuck Stitch)
F-3
These stitches are used to join together seams and
finish them in one operation. The Elastic Overlock
Stitche is useful when sewing stretch materials.
1. Set the Pattern Selection Dial to Comb Stitch,
Elastic Overlock Stitch or Elastic Shell Tuck Stitch.
2. Position the fabric under the presser foot so that
the seamline (or arrowhead point) is approxi-
mately 3 mm (1/8") to the left of the center of the
presser foot. This stitch works best with a seam
allowance of approximately 6 mm (1/4") as this
allows the right (zigzag) side of the stitch to
overlock the cut edge of the fabric as shown in
fig. A.
3. If the seam allowance is wider than the stitch
pattern, trim away any excess fabric after stitch-
ing.
A finished Elastic Overlock Stitch is shown in fig. B.
When sewing the Slant Overlock Stitch, position the
fabric so that its edge is on the left of the needle. (See
fig. C)
AB C
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother STAR 130E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother STAR 130E in the language / languages: English, Spanish as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother STAR 130E

Brother STAR 130E User Manual - German, Italian - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info