631349

Brother SL7 Manual

24
Zoom out
Zoom in
Previous page
1/67
Next page
16
1. Raise the presser foot using the presser foot lifter and turn the
balance wheel toward you (counterclockwise) to raise the
thread take-up lever to its highest position.
2. Pull up the spool pin and place a spool of thread on this pin.
3. Pass the thread through both thread guides: the rear one first,
then the front one. (fig. A)
a Spool pin
b Thread guide (rear)
c Thread guide (front)
d Thread take-up lever
4. Pull the thread down and around the upper tension control
dial from the right to the left so the thread picks up the thread
check spring. (See fig. B.) While holding the thread as shown
in fig. C, pull it between the tension discs.
e Upper tension control dial
f Thread check spring
5. Guide the thread to the back of the thread take-up lever and
around to the left (fig. D). Bring the thread through the slit by
pulling it toward you and into the eyelet.
g Thread take-up lever
6. Bring the thread down and pass it behind the thread guide.
h Thread guide
7. Thread the needle from front to back and pull out about 5 cm
(2") of thread as shown in fig. E.
NOTE:
If the thread is incorrectly fed, the thread may break, cause
stitches to be skipped or cause the fabric to wrinkle.
1. Lever le pied-de-biche à l’aide du levier correspondant et
tourner le volant à main vers soi (dans le sens contraire aux
aiguilles d’une montre) pour remonter complètement le levier
releveur.
2. Lever le porte-bobine et y placer une bobine de fil.
3. Faire passer le fil par les deux guide-fils: d’abord l’arrière puis
l’avant. (fig. A)
a Porte-bobine
b Guide-fils (arrière)
c Guide-fils (avant)
d Levier releveur de fil
4. Tirer le fil vers le bas et le faire passer par le disque de
contrôle de tension supérieure de droite à gauche afin que le
fil attrape le ressort de vérification (voir fig. B). Tirer le fil entre
les disques de tension, tout en le tenant comme le montre la
fig. C.
e Disque de tension du fil
f Ressort de vérification du fil
5. Guider le fil vers l’arrière du levier releveur puis autour vers la
gauche (fig. D). Amener le fil vers la fente en le tirant vers soi
et le faire passer par le chas.
g Levier releveur
6. Tirer le fil vers le bas et le faire passer derrière le guide-fils.
h Guide-fils
7. Enfiler l’aiguille de l’avant vers l’arrière et tirer environ 5 cm
(2") de fil comme le montre la fig. E.
REMARQUE:
Si le fil n’est pas installé correctement, il peut se rompre, causer
des sauts de points ou des fronces dans le tissu.
1. Levante el prensatelas con la palanca y gire la ruedecilla hacia
usted (en el sentido contrario al de las manecillas de un reloj)
para subir la palanca tirahilos a su posición más alta.
2. Levante el porta carretes y coloque un carrete en el eje.
3. Pase el hilo a través de ambas guías: la de atrás primero y luego la
de delante. (fig. A)
a Porta carretes
b Guía hilo (trasera)
c Guía hilo (delantera)
d Palanca tirahilos
4. Tire del hilo hacia abajo, pasando por el disco de control de la
tensión superior de derecha a izquierda de tal forma que el hilo
enganche el resorte de comprobación del hilo. (Véase fig. B).
Mientras sujeta el hilo tal como indica la fig. C, páselo por los
discos de tensión.
e Disco de tensión del hilo
f Resorte de comprobación del hilo.
5. Guíe el hilo por detrás de la palanca tirahilos y por la izquierda
(fig. D). Lleve el hilo por la ranura, tirándolo hacia usted y
pasándolo por el agujero.
g Palanca tirahilos
6. Baje el hilo y páselo por detrás de la guía.
h Guía
7. Enhebre la aguja de delante hacia atrás y saque unos 5 cm (2") de
hilo tal como indica la fig. E.
NOTA:
Si el hilo está mal enhebrado, puede romperse, saltar puntadas o
fruncir el tejido.
1. Levante o calcador com a alavanca e gire com a mão o volante, na
sua direção (para a esquerda) para lerantar ao máximo o estica-fio.
2. Levante o portacarretel e coloque no seu eixo um carretel de
linhas.
3. Passe a linha através dos dois guia-fios: primeiro o posterior, e em
seguida o anterior. (fig. A.)
a Porta-carretel
b Guia-fio (posterior)
c Guia-fio (anterior)
d Estica-fio
4. Puxe a linha para baixo e contorne o botão de regulagem da tensão
da linha superior, da direita para a esquerda, de forma que a linha
passe pela mola de tensáo da linha. (Veja a fig. B.) Segurando na
linha da forma indicada na fig. C, puxea com força para encaixala
entre os discos tensores (do botão).
e Botão tensor da linha
f Mola de tensáo da linha
5. Guie a linha para a parte de trás do estica-fio e em seguida para a
esquerda (fig. D); Passe-a através da fenda puxando-a para si e
enfie-a no orifício do estica-fio.
g Estica-fio
6. Puxe a linha para baixo e passe-a por detrás do guia-fio.
h Guia-fio
7. Enfie a linha na agulha da frente para trás e puxe cerca de 5 cm de
linha, conforme mostra a fig. E.
NOTA:
Se a linha não estiver corretamente passada, poderá partir-se
provocando falha de pontos ou franzir o tecido.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother SL7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother SL7 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother SL7

Brother SL7 User Manual - German, Dutch, French, Italian - 66 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info