456614

Brother PX 300 Manual

34
Zoom out
Zoom in
Previous page
1/88
Next page
25
KNOWING YOUR SEWING MACHINE
CONOZCA SU MÁQUINA DE COSER
CONNAÎTRE SA MACHINE À COUDRE
Lower Threading
Turn power switch to “O”.
1. Raise the needle to its highest position by turning the balance wheel
toward you (counterclockwise) and raise the presser foot lever.
2. Open the shuttle cover behind the extension table on the front of
the machine and remove the bobbin case by pulling its latch to-
ward you and pulling it out from the shuttle race (fig. A).
3. Unwind about 10 cm (4") of thread from a full bobbin and insert
the bobbin into the bobbin case. (See fig. B-1.) Pull the trailing
thread into the slot, then down and to the left, as shown in fig. B-2,
until it enters the delivery eye under the tension spring (fig. B-3).
4. Holding the bobbin case by the latch, fully insert the bobbin case
into the shuttle race and release the latch. Make sure the bobbin
case finger fits into the notch at the top of the race as shown in fig.
C.
NOTE:
If the bobbin case is not properly placed back into the machine, it will
fall out from the shuttle immediately after starting to sew.
1 Bobbin case latch
2 Bobbin case finger
3 Tension spring
4 Notch
“CAUTION” - “MOVING PARTS-TO REDUCE THE RISK OF INJURY,
DISCONNECT FROM SUPPLY CIRCUIT BEFORE SERVICING. RE-
PLACE COVER.”
12
24
A B-1
B-2
C
B-3
3
Enhebrado inferior
Desenchufar la máquina, interruptor principale a “O”.
1. Levante la aguja a su posición más alta, girando la ruedecilla
hacia usted (en sentido contrario al de las manecillas de un reloj)
y levante la palanca del prensatelas.
2. Abra la tapa del soporte para accesorios, en la parte delantera
de la máquina, y retire el portacanillas de la máquina, tirando de
la uñeta metálica (pestillo) hacia usted y sacándola de la lanza-
dera (Ver fig. A.)
3. Tire unos 10 cm (4") de hilo de una canilla llena e inserte la cani-
lla en el portacanillas. (Ver fig. B-1.) Tire del hilo suelto y páselo
por la hendidura, abajo y hacia la izquierda, tal como se indica en
la fig. B-2, hasta que el hilo pase por la abertura de salida debajo
del resorte de tensión. (fig. B-3)
4. Sujetando el portacanillas por la uñeta metálica, introdúzcalo en
la lanzadera y suelte el pestillo. Asegúrese de que la uñeta metá-
lica del portacanillas se encaje en la hendidura en la parte supe-
rior de la anilla tal como se indica en la fig. C.
NOTA:
Si el portacanillas no se encuentra bien colocado en la máquina se
saldrá de la lanzadera inmediatamente después de empezar a co-
ser.
1 Pestillo del portacanillas
2 Uñeta del portacanillas
3 Resorte de tensión
4 Hendidura
Mise en place du fil inférieur
Mettre l’interrupteur principal sur “O”.
1. Remonter complètement l’aiguille en tournant le volant vers soi (dans
le sens opposé aux aiguilles d’une montre) et relever le levier du pied-
de-biche.
2. Ouvrir le couvercle de la navette, derrière la table d’extension, à l’avant
de la machine, et retirer le boîtier de la canette en tirant la languette
métallique vers soi pour le sortir de la coursière. (fig. A)
3. Dévider environ 10 cm de fil de la canette pleine et insérer la canette
dans le boîtier. (Voir fig. B-1.) Faire passer le fil qui dépasse dans la
fente, en bas et vers la gauche, comme illustré sur la fig. B-2, jusqu’à ce
qu’il s’insère dans l’orifice de sortie sous le ressort de tension (fig. B-3).
4. Tout en tenant le boîtier par le loquet métallique, l’enfoncer à fond dans
la navette et relâcher la languette métallique. Bien veiller à ce que la
languette métallique du boîtier s’introduise dans l’encoche en haut de la
glissière, comme le montre la fig. C ci-dessous.
REMARQUE:
Si le boîtier n’est pas placé correctement, il va s’échapper de la navette dès
qu’on commence à coudre.
1 Loquet du boîtier
2 Languette du boîtier
3 Ressort tenseur
4 Encoche
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother PX 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother PX 300 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother PX 300

Brother PX 300 User Manual - German, Dutch - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info