456614
17
Zoom out
Zoom in
Previous page
1/88
Next page
8
KNOWING YOUR SEWING MACHINE
CONOZCA SU MÁQUINA DE COSER
CONNAÎTRE SA MACHINE À COUDRE
Changing the Presser Foot
It may be necessary to change the presser foot according to your sew-
ing needs.
SNAP-ON TYPE
Turn power switch to “O”.
1. Raise the needle to its highest position by turning the balance wheel
toward you (counterclockwise) and raise the presser foot lever.
2. Release the foot by raising the lever located at the back of the presser
foot holder assembly.
3. Place a different presser foot on the needle plate so that the bar on
the presser foot is in line with the slot in the presser foot holder.
4. Lower the presser foot lifter and fix the presser foot onto the holder.
If the presser foot is in the correct location, the bar should snap into
place.
Cambio del prensatelas
Según sus necesidades de costura, puede ser necesario cambiar el
prensatelas.
Modelo a presión
Desenchufar la máquina, interruptor principale a “O”.
1. Levante la aguja a su posición más alta, girando la ruedecilla
hacia usted (en el sentido contrario al de las manecillas de un
reloj) y levante la palanca del prensatelas.
2. Suelte el prensatelas levantando la palanca que hay en la parte
trasera del soporte.
3. Coloque otro prensatelas en la placa de agujas de tal forma que
la barra del prensatelas quede alineada con la ranura del soporte
del prensatelas.
4. Baje la palanca del prensatelas y fije el prensatelas en el sopor-
te. Si el prensatelas está bien colocado, la barra debe engan-
charse en su lugar correspondiente.
Changement de pied-de-biche
En fonction des besoins, il peut s’avérer nécessaire de changer le pied-de-
biche.
MODELE A CLIQUET
Mettre l’interrupteur principal sur “O”.
1. Remonter complètement l’aiguille en tournant le volant vers soi (dans
le sens opposé aux aiguilles d’une montre) et remonter le levier du pied-
de-biche.
2. Libérer le pied en levant le levier situé à l’arrière du support.
3. Placer un pied différent sur la plaque à aiguille de sorte que la tige du
pied-de-biche s’aligne avec la fente située dans l’axe du pied-de-biche.
4. Abaisser le levier du pied-de-biche et fixer le pied sur l’axe. Si le pied-
de-biche est correctement installé, la tige devrait se mettre en place avec
un déclic.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother PX 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother PX 300 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother PX 300

Brother PX 300 User Manual - German, Dutch - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info