631322
30
Zoom out
Zoom in
Previous page
1/90
Next page
21
KNOWING YOUR SEWING MACHINE
CONOZCA SU MÁQUINA DE COSER
CONNAITRE SA MACHINE A COUDRE
THREADING THE MACHINE
Winding the Bobbin
CAUTION
If the thread spool and/or spool cap are set incorrectly,
the thread may tangle on the spool pin.
Use the spool cap (large, medium, or small) that is
closest in size to the thread spool. If a spool cap smaller
than the thread spool is used, the thread may become
caught in the slit on the end of the spool.
1. Place the spool of thread on the horizontal spool pin and firmly
hold it with a spool cap so that the spool of thread will not turn.
Pass the thread through the thread guide as shown following the
dotted line on the top of the machine.
CAUTION
Use only bobbins recommended by the manufacturer of
this machine (see page 3). Using other bobbins may result
in damage or injury.
2.
Pass the end of the thread through the hole on the bobbin from the inside.
Place the bobbin onto the bobbin winder shaft and slide the bobbin
winder shaft to the right. Turn the bobbin clockwise, by hand, until
the spring on the shaft slides into the groove of the bobbin.
1 Spring on the shaft
2 Groove of the bobbin
3 Bobbin winder seat
4 Bobbin winder shaft
3. While holding the end of the thread, gently depress the foot
controller to wind the thread around the bobbin a few times.
Then stop the machine.
Trim the excess thread above the bobbin.
4. Press down on the foot controller to start.
5. After the machine stops automatically when the bobbin is full,
take your foot off of the foot controller.
CAUTION
When removing the bobbin, do not pull on the bobbin winder
seat. Doing so could loosen or remove the bobbin winder seat,
resulting in damage to the machine.
6. Cut the thread, slide the bobbin winder shaft to the left and
remove the bobbin.
NOTE:
The needle bar does not move when the bobbin winding shaft is
slid to the right.
Immediately after winding the bobbin, it is normal to hear the
sound of the clutch engaging when beginning to sew or manually
turning the handwheel.
CAUTION
Be sure to follow the process described. If the thread is not
cut completely, and the bobbin is wound, when the thread
runs low it may tangle around the bobbin and cause the
needle to break.
CAUTION
Setting the bobbin improperly may cause the thread ten-
sion to loosen, breaking the needle and resulting in injury.
1 Wound evenly
2 Wound poorly
1
2
1
4
3
2
12
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother PS-3700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother PS-3700 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info