606044

Brother PS-2400 Manual

79
Zoom out
Zoom in
Previous page
1/93
Next page
72
MAINTENANCE
MANTENIMIENTO
Automatic Thread Cutting
(Model PS-2500, STAR140E)
NOTE:
Do not operate the Thread Cutter Lever while sewing
or when there is no fabric in the sewing machine.
Threads may become tangled or other problems
may be incurred.
* When sewing with thread thicker than #30 or with
nylon, metallic and other specialty threads, cut
the threads with the thread cutter on the left side
of the machine. Sewing without cutting the threads
or with a needle thread that is too short may cause
the threads to become tangled.
* Normally, the Thread Cutter Lever will move up
and the sewing machine will stop operating after
the threads are cut. However, the Thread Cutter
Lever may stay down when certain threads and
fabrics are used. If this occurs, slightly turning the
balance wheel will allow the lever to move up.
Starting to sew with the Thread Cutter Lever
down will cause it to move up; and a problem may
occur.
* Depending on the type of thread and fabric used,
the needle may stay down near the needle plate
after the threads are cut. This is not a malfunction.
If this prevents the fabric from being removed
from the machine, slightly turn the balance wheel
away from you and raise the needle.
* Do not operate the Thread Cutter Lever when
sewing with the twin needle. The threads may
become tangled. During twin needle sewing, al-
ways cut the threads with the thread cutter on the
left side of the machine.
If the Thread Cutter Lever stays down and the
sewing machine cannot be used, raise the Thread
Cutter Lever and check for the conditions mentioned
on page 72. If the Thread Cutter Lever stays down,
turn the balance wheel to raise the needle and raise
the Thread Cutter Lever to its original position.
Cortahilos automático
(Modelo PS-2500, STAR140E)
NOTA:
No accione la palanca del cortahilos mientras cose
o si no hay tejido en la máquina. Ello podría causar
problemas, como por ejemplo un enredo en los
hilos.
* Al coser con hilos de un grosor superior a # 30 o
con hilo de nylon, metálico u otros hilos especiales,
corte los hilos con el cortahilos situado en la parte
izquierda de la máquina. Si cose sin cortar los
hilos o con una aguja demasiado corta, corre el
riesgo de que se enreden los hilos.
* Normalmente, después de cortar los hilos la
palanca del cortahilos se levantará y la máquina
de coser se desconectará. Sin embargo, para
algunos hilos o tejidos, puede que la palanca del
cortahilos no se levante. En tal caso, gire
ligeramente la ruedecilla para levantar la palanca.
Si empieza a coser con la palanca del cortahilos
bajada, ésta se levantará, pero esta operación
puede ocasionar problemas.
* En función del tipo de hilo o de tejido que utilice,
la aguja puede permanecer bajada al lado de la
placa de agujas después de cortar los hilos. No
se trata de un problema en el funcionamiento. Si
ello impide que se pueda retirar el tejido de la
máquina, gire ligeramente la ruedecilla en
dirección opuesta a usted y levante la aguja.
* No accione la palanca del cortahilos mientras
cose con aguja doble, ya que podrían enredarse
los hilos. Al coser con aguja doble, corte siempre
los hilos con el cortahilos situado en la parte
izquierda de la máquina.
Si la palanca del cortahilos permanece bajada y no
puede utilizar la máquina de coser, levante la palanca
y compruebe que se cumplen las condiciones
indicadas en la página 72. Si la palanca del cortahilos
permanece bajada, gire la ruedecilla para levantar la
aguja y lleve la palanca del cortahilos a su posición
original.
… 79 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother PS-2400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother PS-2400 in the language / languages: English, Spanish as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info