631318
16
Zoom out
Zoom in
Previous page
1/45
Next page
15
THREADING THE MACHINE
Winding the Bobbin
1
Put the spool of thread on the spool pin and
pass the thread around the bobbin-winding
tension disc.
1 Bobbin-winding tension disc
2 Bobbin-winding shaft
2
Pass the end of the thread through the hole on
the bobbin from the inside of the bobbin.
3
Put the bobbin onto the bobbin-winding shaft
and slide the bobbin-winding shaft to the
right. Turn the bobbin clockwise, by hand,
until the spring slides into the slit.
1 Spring
2 Slit
4
While holding the end of the thread, gently
press the foot controller to wind the thread
around the bobbin a few times. Then, stop the
machine.
5
Trim the excess thread above the bobbin and
continue winding the thread onto the bobbin
by pressing the foot controller.
Note
The machine stops automatically when the
bobbin is full.
6
After the machine stops, cut the thread, slide
the shaft to the left, and then remove the
bobbin.
Note
The needle bar does not move after the
bobbin-winding shaft is slid to the right.
Immediately after winding the bobbin, it is
normal to hear the sound of the clutch
engaging when beginning to sew or turning
the balance wheel.
Only use the bobbin (part code: SA156,
SFB (XA5539-151)) that has been
designed for this sewing machine. Using
of any other bobbin may cause damage
to the machine.
The bobbin was designed specifically for
this sewing machine. If bobbins from older
models are used, the machine will not
operate correctly. Use only the enclosed
bobbin or bobbins of the same type (part
code: SA156, SFB (XA5539-151)).
If the spool of thread is not in the right
place, the thread may tangle on the spool
pin.
CAUTION
Actual size
11.5 mm
(7/16")
2
1
CAUTION
1
2
XL5000us.book Page 15 Tuesday, November 11, 2003 9:25 AM
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Prestige 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Prestige 50 in the language / languages: English as an attachment in your email.

The manual is 1,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Prestige 50

Brother Prestige 50 User Manual - German - 45 pages

Brother Prestige 50 User Manual - Dutch - 45 pages

Brother Prestige 50 User Manual - French - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info