718890
225
Zoom out
Zoom in
Previous page
1/244
Next page
APPENDIX
223
7
Error messages
If the start/stop button is pressed while the machine is not correctly set up or if an incorrect operation is
performed, the machine stops and informs you of the error with a buzzer and an error message. If an error
message appears, correct the problem according to the instructions in the message.
To close the message, touch or perform the correct operation, then touch . If the message
appears again, consult your nearest authorized Brother dealer.
Some malfunction occurred. There are too many characters in the
curved text arrangement for the
selected embroidery frame.
Change the text arrangement or the
embroidery frame.
Machine cannot receive any data from
the PC in the Link mode.
Turn off the machine, and check the
USB connection. After connect the USB
cord securely, turn on the machine
again. (Refer to page 142)
The installed embroidery frame is too
small.
Check which embroidery frames can be
used, and then install a larger
embroidery frame. (Refer to page 42.)
The upper thread broke, the thread
came out of the thread tension disc or a
thread guide, or the machine is not
threaded correctly.
Check that the thread passes under the
upper and middle thread guides, and
correctly thread the upper thread. (Refer
to page 50.) If the thread is not broken,
clean the thread guides and the tension
unit. (Refer to page 213.)
The bobbin thread broke or ran out.
Check that there is thread on the bobbin
and that approximately 50 mm (2
inches) of thread has been pulled out,
and then re-install the bobbin. (Refer to
page 33.)
Lint or dust has accumulated in the
thread tension disc.
Remove the tension dials, and then
remove any lint or dust accumulated
between the felt washers. (Refer to
page 213.)
The thread tension is too tight.
Check the tensions of the upper thread
and bobbin thread, and then adjust
them. (Refer to page 102.)
* Since there may be many other causes, refer to the Troubleshooting table.
The upper thread breaks. (Refer to page 219.)
The bobbin thread breaks. (Refer to page 220.)
* Touch to move the needle back or forward. (Refer to page 97.)
The patterns you are editing take up
too much memory, or you are editing
too many patterns for the memory.
225


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother PR-670E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother PR-670E in the language / languages: English as an attachment in your email.

The manual is 11,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother PR-670E

Brother PR-670E User Manual - German - 244 pages

Brother PR-670E User Manual - Dutch - 244 pages

Brother PR-670E User Manual - French - 244 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info