618165
215
Zoom out
Zoom in
Previous page
1/229
Next page
Appendix ——————————————————————————————————————————————————————————
196
There are loops in
the upper thread.
The thread tension does not
correspond to the amount that
the thread tension knob was
tightened.
If the thread tension cannot be
adjusted, thread wax and dust
may have collected in the
subtension thread tension disc
at the front and back of the
thread tension knob, causing the
thread tension disc to rise. Clean
the thread tension disc.
The thread quality is poor.
Try sewing with different thread.
If the problem no longer occurs
after the thread is changed, the
thread quality is the problem.
Replace the thread with one of
good quality.
The machine is
noisy.
Lint may be wound in the hook. Clean the hook. p.183
The upper thread is not threaded
correctly.
Check the thread path, and then
thread the upper thread again.
p.35
The hook is damaged.
Replace the hook.
Consult your nearest authorized
dealer.
Not enough oil was applied. Oil recommended parts. p.186
The needle
threader cannot
be used.
The needle is not at the correct
position.
Touch the key to move the
desired needle bar to be
threaded into embroidering
position.
p.40
Recommended needles are not
used on this machine.
Replace and use recommended
needle.
p.15, 61
The needle is not installed
correctly.
Correctly install the needle. p.15, 61
The hook on the automatic
needle-threading mechanism is
bent.
Consult your nearest authorized
dealer.
p.15, 61
The thread
tension is
incorrect.
The upper thread is not threaded
correctly.
Check the thread path, and then
thread the upper thread again.
p.35
The bobbin thread is not
correctly threaded.
Correctly thread the bobbin
thread.
p.19
The lower thread tension is
incorrect.
Adjust the tension of the bobbin
thread.
p.83
The upper thread
comes out of the
needle when
embroidering
begins.
If a short length of thread
remains after the thread is
trimmed, the needle may
become unthreaded when
embroidering begins again.
Set the remaining length of
thread to “LONG TAIL” on the
second page of the settings
screen.
p.150
The upper thread
does not reach the
bobbin thread
when
embroidering
begins.
There is no more thread in the
bobbin, the thread does not feed
from the bobbin, or the thread
that is fed from the bobbin is too
short.
Correctly thread the lower
thread.
p.19
Although the
thread is not
broken, a broken
thread error
occurs and the
machine stops.
If the thread breakage sensor in
the thread tension disc of the
thread tension knobs cannot
detect that the thread is being
fed, even if the machine is
running, a broken thread error
occurs and the machine is
stopped. If the thread came out
of the thread tension disc, even
though the thread is not broken,
the machine detects that the
thread is not being fed and stops.
Correctly pass the thread
through the thread tension disc.
If the broken thread error occurs
after the machine is rethreaded,
the sensor may be damaged.
Consult your nearest authorized
dealer.
p.37
Symptom Probable Cause Remedy Reference Page
Sapphire.book Page 196 Friday, August 1, 2003 9:12 AM
215


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother PR-600C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother PR-600C in the language / languages: English as an attachment in your email.

The manual is 13,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother PR-600C

Brother PR-600C User Manual - German - 227 pages

Brother PR-600C User Manual - Dutch - 227 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info