555759
11
Zoom out
Zoom in
Previous page
1/51
Next page
6
Changing Needles and Light Bulb
Note
Please make sure power is off before carrying out
the following operations. There is a chance of injury
if the machine accidentally starts running during
this operation.
Changing the Needle
1 Turn the sewing ma-
chine off. Raise needle
to highest position us-
ing hand wheel, and
lower presser foot.
2 Loosen screw with
screwdriver, and re-
move needle.
3 Hold the needle with
the flat side to the right,
and insert the needle as
far as it will go. Make
sure needle is screwed
in tightly.
If the needle is not ad-
equately inserted or the
screw is loose, this may
break the needle or
cause a breakdown and
the needle threader will
not work.
Check needles on a flat
surface to make sure
they are not bent.
Changing the Feed Pin
1
Set the feed dogs to vel-
vet position. (See page 5.)
2
Remove needle, presser
foot and needle plate.
3
Lower presser foot and
turn hand wheel until feed
pin is in its highest position.
4
Insert small screwdriver (in-
cluded) as shown in diagram.
Changing Light Bulbs
1 Turn off power.
2 Remove screw from
head.
Note
HLX5 needles should be used; however, Schmetz 130/
705H may also be used under normal circumstances.
Screwdriver
Flat surface
Lay needle on
a flat surface
(such as the needle
plate or a plate
of glass).
The needle should lay
parallel to a surface.
5 While holding spring
with fingertip, lower the
feed pin changer onto
the needle to pick it up.
6
Attach new feed pin to
feed pin changer, lower
and attach while holding
spring with fingertip.
7 Remove screwdriver.
8 Re-attach needle plate,
needle and presser foot.
Note
Please make sure power is off before carrying out
the following operation. The glass plate over the
light bulb will be hot immediately after using the
machine, therefore it is advisable to wait until the
light bulb has had a chance to cool down before
changing bulbs.
3 Remove bulb housing.
4 Unscrew bulb and re-
move.
5 Screw in new bulb.
Sewing Light:
See page 20.
6 Re-attach bulb housing
and tighten screw.
Screwdriver
120V
Light
Bulb
Light
Bulb
230V
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother PQ1500S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother PQ1500S in the language / languages: English, French as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info